WidenersRotoMetals2Titan ReloadingADvertise here
Inline FabricationLee PrecisionMidSouth Shooters Supply

Page 3 of 3 FirstFirst 123
Results 41 to 47 of 47

Thread: Best way to ship brass?

  1. #41
    I think that a lot of people aren't familiar with the USPS website https://www.usps.com/ for their label and packaging needs. You gotta sign up, but that shouldn't be a problem for most. Your delivery postperson might even pic up your outgoing at your house, saving you a trip to the PO.

    Every conceivable Priority Mail container, whether flat rate or not, is available for FREE, delivered to your residence.

    I hardly use MFRB any more because the Regional A box will hold almost as much AND the price is based on weight and ZIP code. My Regional A boxes often ship for anywhere between $6 and $9. A MFRB is way more costly.
    Same way with a Regional B versus a similar FRB.

    Jus' sayin ...

  2. #42
    Boolit Buddy
    Join Date
    Feb 2016
    Location
    Fl.
    Posts
    327

    If it fits it ships BUT we may want more $$ to deliver.

    I use USPS Flat Rate boxes a lot. Never a problem until last week. I packed two MFRB's with brass to ship to Albuquerque NM. First I lined boxes with bubble wrap, then brass went into plastic bag, sealed bag and taped box up. I use a lot of reinforced shipping tape, probably cover 70% of the box with it. When done boxes were tight & square with no bulges. One weighed 22 lbs & other was 25 lbs.
    Mailed them at local PO no problem. When they arrived in Albuquerque things went downhill fast. The person I mailed the brass to got a Postage Due notice for $91.00. He went to the PO& found out they had enacted a new policy, they would only deliver FRB's that looked the same as the FRB boxes they had on display. No exceptions.
    Clearly the packages were mishandled by USPS en route & I'm being penalized for their negligence. The PO refused to budge on the postage due so the brass is on its way back to Fl.
    I tried calling USPS but the estimated wait time to speak to someone is 90 + minutes. Filed a complaint on line (the website isn't complaint friendly) and received a 'we're looking into it & will get back to you' email from our FL PO.
    The boxes I mailed are pictured below as they looked when the forum member I sent them to went to the Albuquerque PO to try negotiating their release.
    The employees at our local PO have always been helpful. Sounds like each PO can make their own policies. If their decision goes against me, my next step is to contact the Regional Postal Inspector. In my opinion, demanding $91.00 additional to deliver the two boxes is plain old extortion.

    Click image for larger version. 

Name:	vic cavasin brass boxes that were  too distorted.jpg 
Views:	28 
Size:	25.8 KB 
ID:	221979

  3. #43
    Boolit Master RogerDat's Avatar
    Join Date
    Nov 2013
    Location
    Michigan Lansing Area
    Posts
    4,983
    I had one lady tell me my SFRB was not acceptable due to all the strapping tape on the edges and corners, along with being covered with clear tape. I printed off the instructions from the USPS web site where it specifically recommends taping edges and corners and covering label with clear tape to protect it. She accepted them after that.

    Only thing I can suggest is look for the directions on taping boxes and reference that. It does state that the FRB has to be in the original size and dimensions and can't be altered or bulging out. But those look like the were "altered" by the post office smashing them. Might want to re-package and submit picture of fresh package to show how the looked when they were sent. I would suggest the strapping tape wrapped only on edges, along flap seam and maybe one across middle and the rest use clear tape.

    One technique I found works for me is I run the tape along the edge and let it stick out at both ends about an inch or so. Then use a razor knife to slit the tape that hangs off the end in line with the seam tape is folded over so I can fold those end flaps of tape over. I think it holds better with the ends anchored and gives a clean line when the other seams are taped over the flaps.

    Bubble wrap imparts no real strength. Packed with tightly stuffed plastic shopping bags from grocery store will provide more protection from collapse. As will cutting a second box in half at two opposing vertical corners and trimming 3/8 inch off the ends of all the flaps and sides so one box just fits inside the other. I do that for lead.

    I'm thinking your best hope is a before picture you create now to go with the after picture. The returned package has a weight and if the contents are moved to new package it will have the same weight providing further proof to the post office inspector that workers basically smashed your box which was fine when it left.
    Je suis Charlie
    Scrap.... because all the really pithy and emphatic four letter words were taken and we had to describe this way of getting casting material somehow.
    Feedback page http://castboolits.gunloads.com/show...light=RogerDat I do trade a bit from time to time.

  4. #44
    Boolit Bub
    Join Date
    Oct 2010
    Location
    Northeastern, Maryland
    Posts
    54
    Small amounts, small frb, padded as needed. Larger amounts, sealed plastic bags (bag in bag) then double taped frb. I have never had an issue. Hope this helps.

  5. #45
    Boolit Buddy
    Join Date
    Mar 2007
    Posts
    131
    I had two bags of once fired Norma brass sent to me from Sweden .One made it to my house and the other was confiscated in Chicago by Homeland Security because they said it had primers in the package .Dumb ***** couldn't understand that they were fired and inert .Never did get them back .

  6. #46
    Boolit Bub
    Join Date
    Oct 2010
    Location
    Northeastern, Maryland
    Posts
    54
    Quote Originally Posted by rondog View Post
    Yeah, tyvek inside the frb. I bought a 1000 pistol cases once, they were just dumped in a lfrb and taped shut. It busted open at some Postal facility, they swept up all the spilled brass and put it back in, taped it up, and sent it on. But they also swept up all the rubber bands, paper scraps, candy wrappers, and whatever else was on the floor with the brass. Friggin' government employees.....
    At least they didn't send you the empty box.

  7. #47
    I usually use ziplock inside a flat rate box and tape well. Seems to work.

Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check