MiHec Brass 358429 HP/ Aluminum 8 Cavity 358429 Keith SWC - RERUN

[Wasalmonslayer]

Put me down for a 8 cavity, aluminum .358 solid. Thank you.
R underscore KARK atATT dot NET

Got you on the list

Thanks!

[Lefty SRH]

Put me down for a .358, 4 cavity HP plain base mold with all the pins.
Schockley at icloud dot com

[Wasalmonslayer]

Put me down for a .358, 4 cavity HP plain base mold with all the pins.
Schockley at icloud dot com

Got you on the list.

Thank you!

[Nicolas]

Hello, I have a question about the tolerances around the .358 or .360. I'm going to cast from range scraps around 9 BHN + 2 % tin. My revolver has throats measuring .358" and I'd like to have bullets that are .360" maximum. May I order a .358 or a .360 ? What kind of tolerances Miha applies on his work ?

[Wasalmonslayer]

Hello, I have a question about the tolerances around the .358 or .360. I'm going to cast from range scraps around 9 BHN + 2 % tin. My revolver has throats measuring .358" and I'd like to have bullets that are .360" maximum. May I order a .358 or a .360 ? What kind of tolerances Miha applies on his work ?

Hello

Miha's mold are usually spot on size wise with wheel weights

Are you using standard lube or pc/hi tek??
I use pc with .358 diam as cast bullet and they size perfect to .358 just a light squish thru and they clean up perfect...

[Nicolas]

Thank you Wasalmonslayer. I use standard lube with a LAM 2. According to your experience, I think I should change the diameter ordered for a .358". Am I right ?

[Wasalmonslayer]

You can size down a .360 real easy in a lam 2 I would get the 360.

[Nicolas]

I ask because I have the MP 453 200 h&g #68 and It throws bullets around .454" with the mentionned alloy. I find it a bit large for a .452" sizing. I have no .35X" mold from MP to be able to make the comparison.

[Wasalmonslayer]

I ask because I have the MP 453 200 h&g #68 and It throws bullets around .454" with the mentionned alloy. I find it a bit large for a .452" sizing. I have no .35X" mold from MP to be able to make the comparison.

I believe the specs on that mold are for it to throw .454.
In these buys when you have a diameter choice he makes them pretty close to spot on.
They may be a thou over but thats the most I've seen.
I have around 15 of his molds and they all are with in a thou of stated diameter.
I have a two cavity of this design already from the last buy and it was ordered as a 360 diam and it casts right at .3605.

[Nicolas]

So, I'm going to stay with the .360" as I cast from a low antimony alloy. It will surely shrink a little bit and give me bullets around .359 or .360". Thank you for your help Wasalmonslayer

[Wasalmonslayer]

If you would like a mold please state what mold and your disguised email address.

Thanks

[Nicolas]

I'm already on the list

[Wasalmonslayer]

Bumpski

[Meatpuppet]

If it is not too late, can I change my DIA from .358 to .360? I'm #1 on the Hi-Tek list (gijoe).

[Wasalmonslayer]

If it is not too late, can I change my DIA from .358 to .360? I'm #1 on the Hi-Tek list (gijoe).

Got you taken care of

[Wasalmonslayer]

We are sitting at 16 and just a handful more to get it in last call.

Tell your friends

[Wasalmonslayer]

Weekly bumpski

[Wasalmonslayer]

Mid week bump for a great mold!

[georgerkahn]

Wasalmonslayer:
I shall be privileged to be on the list, and hopefully purchase one regular lub.:
2 Cavity HP with all pins, top punch, Allen keys, in 0.360", and, one set of handles
Thanks much!
geo

kahngr at potsdam dot edu

[Wasalmonslayer]

Wasalmonslayer:
I shall be privileged to be on the list, and hopefully purchase one regular lub.:
2 Cavity HP with all pins, top punch, Allen keys, in 0.360", and, one set of handles
Thanks much!
geo

kahngr at potsdam dot edu

Thanks my friend!!

That puts us up to 17 molds...