RepackboxLoad DataLee PrecisionInline Fabrication
Titan ReloadingMidSouth Shooters SupplyWidenersReloading Everything
RotoMetals2
Page 10 of 10 FirstFirst 12345678910
Results 181 to 189 of 189

Thread: MIHEC C358-180-RF with Cramer HP Rerun

  1. #181
    Vendor Sponsor

    Lakehouse2012's Avatar
    Join Date
    Dec 2016
    Location
    Holly, Michigan
    Posts
    2,221
    Quote Originally Posted by Lakehouse2012 View Post
    I should have qualified my first post, that postit in each pic is the velocity in the book per each load. I loaded 10 of each type, shot 2 in the barrel and on another day, will setup the chrono to measure actual velocity. There isnt enough distance in the garage to trap the boolits and keep the chrono dry. Though i thought about testing how waterproof it is....

    Sent from my ME302C using Tapatalk
    Here are the measurements i took on each type. Used a Lee hardness tester which im sure isnt the most accurate. But should be the right ballpark

    Im using WW for both, stickons give me soft and the clipons between 15-17 if i carefully sort out all the stickons from clipons.



    Sent from my ME302C using Tapatalk
    Last edited by Lakehouse2012; 11-14-2017 at 10:34 PM.

  2. #182
    Boolit Master
    Lefty SRH's Avatar
    Join Date
    May 2011
    Location
    Athens, AL
    Posts
    2,172
    Haha, no need to get the chrono wet. They may not be terribly expensive but we need to protect them.
    I appreciate your data. I didnt realize clip on weight would get that hard without water dropping.
    "In GOD We Trust"

  3. #183
    Boolit Master
    Join Date
    Feb 2007
    Location
    Soda Springs, Idaho
    Posts
    1,093
    Anyone know if any of these molds are still available? Would like to have a 4 cavity if possible.

    Dick

  4. #184
    Vendor Sponsor

    Lakehouse2012's Avatar
    Join Date
    Dec 2016
    Location
    Holly, Michigan
    Posts
    2,221
    Quote Originally Posted by sixshot View Post
    Anyone know if any of these molds are still available? Would like to have a 4 cavity if possible.

    Dick
    Check MPs website, usually he builds more than just the GB.

    Sent from my SM-G920V using Tapatalk

  5. #185
    I'm A Honcho!
    Wasalmonslayer's Avatar
    Join Date
    Jan 2014
    Location
    Washington
    Posts
    2,139
    Send Miha a private message.

    I am sure he has an over run he would sell you.

  6. #186
    Vendor Sponsor

    Lakehouse2012's Avatar
    Join Date
    Dec 2016
    Location
    Holly, Michigan
    Posts
    2,221
    I hard and soft casted some of these with the penta pins and here are my results. The soft cast gave me a fantastic flower shape. I think these are my new go-to loads...

    Sent from my SM-G920V using Tapatalk

  7. #187
    Boolit Master wonderwolf's Avatar
    Join Date
    Apr 2007
    Posts
    1,653
    Looks great, I hope to get a bunch of these cast up in a few weeks. I think I've come to the conclusion that this class weight of bullet will be the best all around weight after having tried just about 23 different molds going from 75gr up to 225gr soft lead flower on the left looks very promising. Not sure how fast I can shove this bullet out of the carbine just yet but I'm very excited to see.
    Last edited by wonderwolf; 12-16-2017 at 07:33 PM. Reason: can't spell
    My firearms project blog

  8. #188
    Boolit Master wonderwolf's Avatar
    Join Date
    Apr 2007
    Posts
    1,653
    Anybody else finding these are tight in their revolver chambers? My GP-100 5" is fighting these somewhat.

    Other than that the ones I've loaded up have shown very promising accuracy results so far. Even if they are leading a bit.
    My firearms project blog

  9. #189
    Vendor Sponsor

    Lakehouse2012's Avatar
    Join Date
    Dec 2016
    Location
    Holly, Michigan
    Posts
    2,221
    Quote Originally Posted by wonderwolf View Post
    Anybody else finding these are tight in their revolver chambers? My GP-100 5" is fighting these somewhat.

    Other than that the ones I've loaded up have shown very promising accuracy results so far. Even if they are leading a bit.
    The testing i did about was with a GP100 3"(in case i hadnt mentioned). I size all rounds to .358 and i tumble lube with White Lable lube. I ran 150 rounds yesterday and no leading.

    Sent from my SM-G920V using Tapatalk

Page 10 of 10 FirstFirst 12345678910

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check