If you use them, what for and will you buy another when your current one expires?
If you use them, what for and will you buy another when your current one expires?
"Freedom is never more than one generation away from extinction. We didn't pass it to our children in the bloodstream. It must be fought for, protected, and handed on for them to do the same......." - Ronald Reagan
"It is foolish and wrong to mourn the men who died. Rather, we should thank God that such men lived." - George Patton
The second amendment is a nail on which hangs a picture of freedom - member Alex 4x4 Tver, Russia
I have the Harbor Freight one. I bought it to clean scuba regulators. I tried it for cleaning brass with citric acid and dish soap. It does a fair job of cleaning the inside of the case and primer pockets.
I have used it to clean tens of thousands of cases. It does about 300 per load in about 15 minutes.
I rinse and then dry them in my convection oven set at 200. I run them through the tumbler for 10 minutes with walnut shells and Nu Finish.
If it breaks, I would probably get a new one.
There is no difference between communism and socialism, except in the means of achieving the same ultimate end: communism proposes to enslave men by force, socialism—by vote. It is merely the difference between murder and suicide. Ayn Rand
I like mine. I deprime and run thru my Lyman, prior to the tumbler. My walnut media stays clean Forever! Mine also cleans the tiny fog nozzles at our business, works excellent for that purpose too. Yes, I would replace it. hc18flyer
I use them for cleaning difficult guns. EG the 97 Winchester is a bear to totally disassemble and they usually need it as they are crud in everywhere. 1/2 hour in the ultrasonic tank and the action and breech assembly come out without a speck of dirt. I would not be without one any more.
I've got a Hornady and a Harbor Freight. Both work very well with citric acid and a touch of dawn. Rinse and dry in the Arizona sun. Then I polish in corn cob with Nu Finish. They come out looking factory new.
Rifle brass PP generally come out clean if you have 'uniformed' them the first time. I dry by setting cases in plastic pistol ammo holders I find at the range. 50/rack and set them outside in the sun. Good to clean BCG as well as brass. Larger HF one didn't work very well but the small Hornady has lasted 4yrs or so.
Whatever!
I used one several yrs ago to clean up a badly fouled 9mm bbl . I worked so well I used it for a Single Action cylinder . I've off and on looked for the ability to put a bbl'd action in one so I could just pull the wood and leave a rifle to soak in Hoppes with a 30 min cycle on both ends for new to me and whoops that didn't go according to plan .
In the time of darkest defeat,our victory may be nearest. Wm. McKinley.
I was young and stupid then I'm older now. Me 1992 .
Richard Lee Hart 6/29/39-7/25/18
Without trial we cannot learn and grow . It is through our stuggles that we become stronger .
Brother I'm going to be Pythagerus , DiVinci , and Atlas all rolled into one soon .
I got one with intention of using to clean brass. Won't buy again as it is mediocre and still required polishing in media. I replaced it with a Stainless pin tumbler and it does a much better job with more capacity.
Those stress balls really work..... When you get to shove them down a persons throat.
I have a Sharpertek, I bought the "guncleaning" accessory package for it. I use the main tank for cleaning carburetors and have a fairly steady stream of business based on that- every spring lawn mowers won't start, every hurricane people can't start their generators. I have the "sweep" function and a heater that dies a superb job if things. The "Gun Cleaning" accessory is a polycarbonate tank that is filled with oil, it sets into the fluid in the main tank and the ultrasonic waves are transferred to the oil from the fluid. I only use it for REALLY gunked up stuff as it puts a fairly heavy coating of oil on (and in) everything. I've had moderate success with it "unsticking" leading.
I love the ability to clean carbs without major disassembly and it is kind to gaskets and "o" rings.
It did OK on brass.
I think I'd get another Sharpertek...probably a larger one... mine has a hard time with big 4 barreled automotive carbs.
The essence of education is self reliance- T.H. White.
Currently seeking wood carving tools, wood planes, froes, scorps, spokeshaves... etc....
I have one that I use for detail cleaning of mainly old handguns. I use it with carburetor dip cleaner. After they are striped and run through about a 30 minute cycle everything comes out spotless. On tupperware guns I use distilled water and get very good results. I've never tried using it for cleaning brass, I have a couple of large tumblers for that and I'm happy with their results.
I've got the Lyman(medium sized) and have used it for brass,jewelry and guns &a parts.
it roes a good job and when used with a tumbler and walnut media it makes brass look brand new. I would buy another for sure.
I don't have one but I think it would be great at cleaning gun parts. Things like bolts and trigger groups.
I have used Harbor Freight 2.5 Liter Ultra Sonic for about 8 years, and it's still going strong.
http://www.harborfreight.com/25-lite...ner-63256.html
I have run many, many thousands of Pistol and Rifle brass through it using a few drops of Dawn dish soap and some Lemi-Shine as cleaning agent. The Ultra-sonic is great at removing the dirt and crud from range pick ups; fairly good at removing powder fowling on the brass (provided you use the Heat Function with this unit). The brass does tarnish after cleaning in the ultrasonic and drying. A short run through a tumbler for a few minutes addresses this problem. Some will criticize tumbling after Ultrasonic cleaning; but I learned I spend a lot less in Corn Cob or Walnut media by doing an Ultrasonic clean first as it does not load the tumbling media with dirt and crud doing this.
Mustang
"In the beginning... the patriot is a scarce man, and brave and hated and scorned. When his cause succeeds, the timid join him, for then it costs nothing to be a patriot." - Mark Twain.
Mine were free. Deceased father in law was a watchmaker.
They are nice for cases that need cleaning but aren't needing heavy cleaning action.
Cleaning gun parts... very effective with simple green on cosmaline coated parts when my latest C&R shows up. Would definitly buy another should the need arise.
Last edited by Kevinakaq; 04-26-2017 at 07:59 PM.
“I won't be wronged. I won't be insulted. I won't be laid a hand on. I don't do these things to other people and I require the same from them." the duke
I have the harbor freight unit. I mainly use mine for cleaning carburetors and gun parts and yes I would replace it when it dies
OK so I know nothing about the sonic cleaners...was thinking of getting the HF one just for cleaning small stubborn parts. Can the 2.5L model handle mineral spirits type cleaners or can it only be water based?
After reading thru all the threads on ultrasonic cleaners I figured this one was about the best. Some knock ultrasonic cleaning in general based on the purchase of some brands of cleaners which may in fact be questionable. While ultrasonic cleaning isn't going to bring back the 100% new brass shine it certainly if worth both the time and effort. The best ultrasonic cleaning job I saw was from my brothers garage. He put some absolutely black looking brass into his $500 ultrasonic cleaner for ten minutes and they came out looking almost like new only missing that mirror shine one would expect from new brass. He then dried the brass and put it into his large Dillon tumbler with some Lyman brass polish and the result was brass looking like it just came out of the box from the manufacturer.
Personal opinion here.... A good ultrasonic clean requires some type of cleaning agent as well as hot temp and good ultrasonic action. This is where you separate the men from the boys. The cheap cleaners dont heat up to a decent temp and or take hours to reach the temp wheras the more costly units have say 400 watt heaters and multiple ultrasonic devices.
Just ordered a close out from Walmart. List price is $900+ and its on a reduction to $202 plus change. Stainless steel unit lots of room and ability to heat. Looking forward to getting it.
I have a stainless one that heats and love it.
Well I got my ultrasonic cleaner I had ordered from Walmart. Its a great piece of equipment and bigger than I had thought it would be. Now to come up with the perfect cleaning solution mix.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |