Wisconsin TriggerInline FabricationMidSouth Shooters SupplyStainLess Steel Media
Titan ReloadingLee PrecisionRotoMetals2

Results 1 to 18 of 18

Thread: S&W K38 strength

  1. #1
    Boolit Master

    Join Date
    Feb 2008
    Location
    Grover Beach, CA. just ahead of Pismo Beach
    Posts
    507

    S&W K38 strength

    I have an older K38, pre-model numbers, in excellent condition. I mostly shoot light target load but would like to shoot some +P loads. Will the K38 hold up to a steady diet of the heavier loads. I don't want to do anything that will damage the gun.

    Thanks
    Carl

  2. #2
    Boolit Master TenTea's Avatar
    Join Date
    Mar 2013
    Location
    Wisconsin
    Posts
    541
    Pre 14 & 15 Masterpieces were not designed for +P.

    Will the gun be damaged by a *steady diet* of hot loads?
    Probably not, but maybe...why abuse that sweet old steel?
    Find a revolver rated for +P.

    *the above is my opinion, fwiw
    A bear, however hard he tries, grows tubby without exercise.

  3. #3
    Boolit Master

    Join Date
    Mar 2011
    Location
    oklahoma
    Posts
    1,435
    While it probably would be just fine, there isn't much difference in standard .38 spcl and .38 spcl +P. I'd just stick with a higher end standard level load if it were mine.

  4. #4
    Boolit Master
    TCFAN's Avatar
    Join Date
    Feb 2006
    Location
    Missouri Ozarks
    Posts
    1,014
    If that was my revolver I would stay with target wadcutters and enjoy that old classic S&W.If you want to shoot hotter loads then look at a 686 or a GP100. Just my opinion for what it is worth..........

  5. #5
    Boolit Master Outpost75's Avatar
    Join Date
    May 2013
    Location
    over the hill, out in the woods and far away
    Posts
    5,025
    While limited use of +P is not dangerous, it WILL loosen the gun more quickly. Pre-1957 K-frames have soft frames which are only about 90 Rockwell B scale. Firing +P will stretch the frame, increase cylinder gap and end play. The end shake can be corrected by stretching the crane, but cylinder gap will then be increased by the amount of end-shake eliminated. This can usually be done twice before barrel-cylinder gap increases above the S&W Customer Service maximum of pass 0.008" / hold 0.009".

    If cylinder gap is already close to the maximum, correction will require setting the barrel back a thread and refitting the cylinder and yoke and recutting the forcing cone, about a $200 repair in most shops.

    My advise is to limit any firing of your K38 to STANDARD pressure loads and that any use of +P should be limited to one box spread over the life of the gun, for emergency use only.

    Otherwise you are turning a nice $600-700 gun into a $300 gun requiring $200 of gunsmithing work to bring it up to a $500 used gun.
    The ENEMY is listening.
    HE wants to know what YOU know.
    Keep it to yourself.

  6. #6
    Boolit Master

    376Steyr's Avatar
    Join Date
    Aug 2006
    Location
    South Idaho
    Posts
    1,220
    "Don't do it. You'll regret it afterwards. Is it really worth it?" These words apply both to walking into a bar at 1 a.m. and shooting +P in a classic K38.

  7. #7
    Boolit Master tazman's Avatar
    Join Date
    Jan 2014
    Location
    west central Illinois
    Posts
    3,354
    I own a pre 14 Target masterpiece and it performs well with target wadcutters and standard 38 special loads. For +P I use either a 357 mag or my late model 15.
    I want my Target masterpiece to last forever.

  8. #8
    Boolit Master

    Join Date
    Feb 2008
    Location
    Grover Beach, CA. just ahead of Pismo Beach
    Posts
    507
    Thanks for all of the advice. it is one of the bests shooters I have. Guess I will just keep it that way, besides if I need more power get a bigger gun

    Thanks all. I'm glad I ask

    Carl
    Last edited by chboats; 04-21-2017 at 10:08 AM.

  9. #9
    Boolit Master
    Join Date
    Jul 2015
    Posts
    2,162
    Do you carry the K38? If not I see no reason to use +P. Even modern guns wear out, with standard ammo, it takes a massive amount of shooting to do it. Every gun has a working life, that life is shortened faster with hotter ammo, add in weaker steel, and it is shortened even more. In the 1930's Colt 38 revolvers were approved for 38/44 today equal to +P+, including the small police positive, BUT limited use only.

    I was friends with a detective that still had boxes of factory 38/44, and he carried them in his model 36, but except for one shooting he only used them for carry. The use of hot ammo for practice is way overblown, IMO. In the 70's, and 80's we had much better accuracy compared to current LEO's(Sorry LEO's). Our training schedule was monthly 18 rounds carry ammo, 50 to 100 rounds qualification, plus rotating the ammo in the shotgun.

    The detective that carried 38/44 in his J frame trained with wadcutters like the rest of us. He had no problem hitting the perp holding a knife to a nurse's neck with the two inch revolver. Remember your first shot is the most important, and all those recoil factors do not start until after the first shot.

    My advice would be find a +P revolver with modern steel to train with hot ammo. A used Taurus is around $200 more or less. If you wear it out, so what? Sorry Taurus owners, no offense intended.

  10. #10
    Boolit Master

    Wayne Smith's Avatar
    Join Date
    Mar 2005
    Location
    Hampton Roads, Virginia
    Posts
    9,299
    Thanks for your decision. I have a Colt Agent - it only sees wadcutter ammo, but even for carry that will do the job if necessary - if I need more than that I have no business being there.
    Wayne the Shrink

    There is no 'right' that requires me to work for you or you to work for me!

  11. #11
    Boolit Master
    Join Date
    Nov 2012
    Location
    Central Virginia
    Posts
    4,690
    chboats - you've received good advice.
    I have a K-38 and even though mine is a Model 14 (newer model than yours) I see no reason to abuse that fine gun.

  12. #12
    Boolit Master
    Join Date
    Mar 2005
    Location
    Lincoln, Nebraska
    Posts
    4,959
    Standard velocity handloads get quite adequate velocity. There is no real need for Plus p. For example, 4.7 grains Unique gets about 900 or a bit over with a 158 SWC in my 4 inch M and P, and 5.4 Power Pistol goes faster yet, both standard loads.

    These will do any 38 task worth doing.

  13. #13
    Moderator Emeritus


    Join Date
    Mar 2005
    Location
    SW Montana
    Posts
    11,270
    http://shootingwithhobie.blogspot.co...-saxonpig.html

    Another mans opinion. I believe 38 special was loaded as hot or hotter in the 70's than the current +p loads. I am of the opnion that rapid da shooting is much harder on the gun than slow fire of + p rounds.
    [The Montana Gianni] Front sight and squeeze

  14. #14
    Boolit Master Outpost75's Avatar
    Join Date
    May 2013
    Location
    over the hill, out in the woods and far away
    Posts
    5,025
    When LAPD was buying Model 14s for street use with +P ammo in the 1970s frames and cylinders for contract orders specified heat treatment for frames and cylinders the same as for .357 Model 19s, Rc20 Min., with Rc22-24 desired.
    The ENEMY is listening.
    HE wants to know what YOU know.
    Keep it to yourself.

  15. #15
    Boolit Master


    HangFireW8's Avatar
    Join Date
    Dec 2008
    Location
    Central Maryland
    Posts
    2,086
    Indeed, modern +P 38 Special is barely above the pressure of standard 38 Specials, while old 38/44 is most of a 357Mag.

    -HF

  16. #16
    Boolit Master

    Join Date
    Feb 2008
    Location
    Grover Beach, CA. just ahead of Pismo Beach
    Posts
    507
    The only thing the gun is use for is killing paper targets and ringing the occasional steel plate. I have no need to shoot the hotter load in the K38. I do have a couple of 357s. Just wanted to know. It is easier to win the game if you know ALL the rules.

    Thanks
    Carl

  17. #17
    Boolit Master Char-Gar's Avatar
    Join Date
    Mar 2005
    Location
    Deep South Texas
    Posts
    13,681
    The 38 Special +P is an attempt to get a jacketed HP bullet expand in revolvers of various barrel lengths. If you are not trying to expand a JHP bullet, there no sense in running those pressures.

    I favor the full charge wadcutter for social use against unfriendly human beings. A charge of 3.5 grains of Bullseye over a solid base wadcutter will prove very effective. I prefer the H&G 244 which has a dead flat nose. I like flat and really flat just must be the best. because of the deep bullet seating, the pressures will run higher thought not in the +P range.

    For small game and range use I drop the charge to 3.0 grains of Bullseye.

    Here is a pick of my Chief Special with such loads. I use these same loads in small and medium frame 38 by Smith and Wesson and Colt in various barrel lengths. Works well in all.

    Addendum: This same bullet in 357 Mag cases over either 10/2400 or 7.5/AA5 gives about 1,100 fps and is a cracker jack load for the 357 revolver, giving great accuracy along the way.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	Chief Special small.jpg 
Views:	7 
Size:	63.4 KB 
ID:	193739  
    Last edited by Char-Gar; 04-21-2017 at 01:41 PM.
    Disclaimer: The above is not holy writ. It is just my opinion based on my experience and knowledge. Your mileage may vary.

  18. #18
    Boolit Master
    Join Date
    Jul 2015
    Posts
    2,162
    I carry wadcutters for primary, SWC in the speed loaders. Mine are on the hot side though, 900 fps 138 grain 5.5 grain longshot in a 2 inch revolver. In the GP100 4" with 6.0 grains longshot they are cooking at 1200 fps. They are Bayou Bullets coated wadcutters to avoid leading. These are carry only, of course I had to shoot them for development.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check