I like to ask the Lyman m die will it work with cast booklets
.358 .L spoke with Lyman they said no plug that big
I like to ask the Lyman m die will it work with cast booklets
.358 .L spoke with Lyman they said no plug that big
You can use the Lee universal expanding die. It will do just about any caliber. I have one and it works quite well.
Sent from my iPhone using Tapatalk
I use the M die with .357 for 9mm.
Last edited by farmerjim; 03-26-2017 at 01:59 PM.
There is no difference between communism and socialism, except in the means of achieving the same ultimate end: communism proposes to enslave men by force, socialism—by vote. It is merely the difference between murder and suicide. Ayn Rand
Get the NOE neck expanders that work with the LEE Universal Expander. You'll be pleased. Pick which one you need.
http://noebulletmolds.com/NV/index.p...ka80vu5stqdls2
Shiloh
Je suis Charlie
"A society of sheep must in time beget a government of wolves."
Bertrand de Jouvenel
“Any government that does not trust its citizens with firearms is either a tyranny, or planning to become one.” – Joseph P. Martino
“If you put the federal government in charge of the Sahara Desert , in five years there would be a shortage of sand.” – Milton Friedman
"Ideas are more powerful than guns. We would not let our enemies have guns; why should we let them have ideas?" - J. Stalin
Semper Fi!
Currently casting for .223, .308, .30-06, .30-40 Krag, 9mm, .38/.357, 10mm, 44 Mag and 45 ACP.
I like strange looking boolits!
NRA Patriot Life Endowment member.
Get a lee universal expanding die and an NOE expanding plug to go inside. NOE has both of them.
It's only hubris if I'm wrong.
Yes, the Lyman M-die/expander that came with the die set will work with .358 bullets. It will flare the case mouth (just as the Lee does) and expand the inside for .355 - .356 bullets. Thus you're putting a bullet in that is .002 over what is intended. If the bullet is too soft it may get sized down is all. I seat .357 sized cast in 9mms using the standard expanders that come in all 3 of my 9mm dies sets; RCBS, Lee and Dillon SDB. I've also seated cast sized to .360. I get a "coke bottle" effect and suspect you will too. No problems though.
Larry Gibson
Any one here have any idea if any member on the form can make me a plug in .358 for the Lyman m die
Get the NOE version as noted above
http://noebulletmolds.com/NV/index.p...77jugo3gam3di5
You will need the Lee die body which is round $10 to 15
Last edited by jmort; 03-25-2017 at 03:41 PM.
I am using a Lyman M Die to expand my 9mm brass.
The sooner I fall behind...the more time I have to catch up with
I use Lyman m-dies (well, their multi-expander actually, but the plugs are the same) and size all my 9mm boolits to .358", no problem. https://www.midwayusa.com/product/74...der-charge-die
This set-up works very well with my RCBS turret press and Redding powder measure.
I also have a bunch of NOE plugs of various sizes, and the Lee Universal Expander. Etc. etc.
Last edited by Boolseye; 03-26-2017 at 11:30 AM.
Je suis Charlie
"A society of sheep must in time beget a government of wolves."
Bertrand de Jouvenel
“Any government that does not trust its citizens with firearms is either a tyranny, or planning to become one.” – Joseph P. Martino
“If you put the federal government in charge of the Sahara Desert , in five years there would be a shortage of sand.” – Milton Friedman
"Ideas are more powerful than guns. We would not let our enemies have guns; why should we let them have ideas?" - J. Stalin
I use the powder through expander die for the 38 S&W, works like a charm !
https://www.midwayusa.com/product/20...set-38-s-and-w
I think you can locate just the case mouth expander at Titan Reloading (top of page).
Not to mention that since I recently moved my reloading of 9mm's to my LEE Load-Master it makes things go a lot smoother.
No more cases squeezing my boolits down !
CPL Lou
CPL Lou
That is a great idea, and they're only $3!! Can anyone tell me what the outside diameter of this expander is? Thanks!I use the powder through expander die for the 38 S&W, works like a charm !
https://www.midwayusa.com/product/20...set-38-s-and-w
I shoot so that I can handload.
I will say the M die did shoot a tighter group I did adjust the M die to seat a tad deeper and it work out great.
I went with stage 1 Lee resizing die
Stage 2 M die
Stage 3 Lee powder expander die set up just enough to activate the powder drop
Stage 4 lee seating die
I drop 3.6 grains of Bullseye with a 122 gr. F.P. bullet
Group size at 12 yards two hand hold unsupported well under 1 1/2"
Ruger SR9
the fired case had no blow by at all clean as a whistle
I think I am going to order another M die for my 1911
Is there a thread that discusses the NOE expander plugs? I've got a couple of M dies but I can't say I've used them enough to be familiar and only on .30 cal. rifle.
What do I need to get in order to use the NOE plugs?
John
W.TN
A Lee universal expander. The NOE plugs drop right in that die. They work wonderfully and are reasonably priced.
Sent from my iPhone using Tapatalk
I shoot so that I can handload.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |