-
* I follow PC Mfgr's directions for temp. & time.
-
* I pre-heat the oven
-
* I don't preheat the oven
-
* I bake longer than recommended time
-
* I bake shorter than recommended time
-
* I use higher temp. than recommended
-
* I use lower temp. than recommended
-
* I have verified my oven's temperature w/separate thermometer
-
* I use a PID Controller on my oven
-
* I use a convection oven
-
* I use a toaster oven
-
* I use a full size kitchen oven
-
* I use a recommended #5 tub
-
* I don't use #5 tub but I use a tub
-
* I ESPC with the casts on a jig
-
* I ESPC w/out a jig
-
* I put them in a container, place it in the vibratory cleaner bowl...let it shake them
-
* I put them in a rock polisher type drum and coat them
-
* I shake them less than a minute
-
* I shake them more than a minute
-
* I slurry coat
-
* I use recommended Black air-soft BB's
-
* I use any color BB's
-
* I don't use BB's
-
* I stand casts individually to bake
-
* I use a jig and bake
-
* I dump and bake
-
* I shake/tap off excess PC
-
* I don't shake/tap off excess PC
-
* I bake on non-stick Aluminum foil
-
* I bake on Parchment
-
* I bake on silicone mat
-
* I dump and bake on wire or mat and oven cool
-
* I dump and bake on wire or mat and air cool
-
* I dump and bake on wire or mat and water drop
-
* I stand or jig and bake and oven cool
-
* I stand or jig and bake and air cool
-
* I stand or jig and bake and water drop
-
* I use Harbor Freight PC
-
* I don't use Harbor Freight PC
-
* I use Smokes PC
-
* I use Powder by the Pound PC
-
* I use Eastwood PC
-
* I use Prismatic PC
-
* I use Sherman Williams PC
-
* I use ___________________PC (give a name of your brand in comments below)
-
* I use hi-tec or other than PC coating
-
* I get good coverage in hi-humidity
-
* I don't coat in high-humidity
-
* I get good coverage only in low-humidity
-
* I get good coverage rain or shine makes no difference
-
* I am satisfied with my coating results
-
* I am not satisfied with my coating results
-
* I want perfect looking coatings
-
* I don't care about perfect, I want quantity
-
* I put more effort into coating high velocity casts than lo-vel pistol casts
-
* I treat them all the same...hi or lo velocity
-
* I PC only the drive bands of my cast
-
* I gas check before I PC
-
* I gas check after I PC
-
* I leave the base of the cast bare of PC
-
* I coat the base of my casts with PC
-
* I have trouble with the PC flashing, making a skirt at the base
-
* I PC as it is my only option
-
* I PC as choice over a Lube-sizer
-
* I still do both
-
* I lube size or tumble or pan lube, to heck with this PC business...gerrrrr!
-
* I cast, size, PC and size again before loading
-
* I cast, PC and size before loading
-
* I cast, size and PC before loading
-
* I cast, PC and don't size before loading
-
* I nose size also
-
* After PC I wait some time before sizing
-
* After PC and-/or not- sizing, I wait some time before loading
-
* To heck with waiting for anything...I load them immediately or whenever I'm ready to use them
-
* I do a smash test for every batch
-
* My method has already passed the smash test long before and now, I don't bother
-
* I smash test only if I think something is wrong
-
* I never smash test
-
* I am satisfied with the accuracy of pistol casts and PC
-
* I am not satisfied with the accuracy of pistol casts and PC
-
* I am satisfied with the accuracy of rifle casts with PC
-
* I am not satisfied with the accuracy of rifle casts with PC
-
* I am not decided yet about accuracy
-
* Most of my problems are attributed to the quality of the PC powder I use
-
* Most of my problems are attributed to my oven temp. control
-
* Most of my problems are attributed to unclean casts
-
* I use nitrite gloves to handle my PC'd casts
-
* I use tweezers or some other tool to handle my PC'd casts
-
* I wear a respirator when I do PC coatings