How many barrels are too many given the state of TC with S&W?
Leadmelter
MI
How many barrels are too many given the state of TC with S&W?
Leadmelter
MI
Don't know, I have four I can remember and likely won't get more. Just make sure you're stocked up on hammer springs and you'll be good to go for a long time.
-Nobade
I think it you get one of every caliber made you should be fine.
John Allen is right but I would get 2 22lr bbl match standard also octogon and then 10", 12", 14" and super 16 and carbine bbl,and........Tim⛲
I this may be blasphemy but I hate changing from rifle to handgun. So my next version has to be a dedicated rifle. I have the handgun. What I like is the selection from custom builders so I highly doubt you have to worry about them disappearing.
I have 4. Three pistols and a carbine.
I have one Contender and two Encores registered as pistols. The Encores have been set up as rifles, and I am going to get another one and set it up as a pistol.
I thinned the herd a few years ago and am down to 3 G-1 pistol frames with a 22 mag, 22 Hornet, 7TCU , 44 mag and 45/410. Should have held on to them as the barrels have increased in price. The encore herd is doing well and growing. Although I really should have a G-2 now that Ed's has them again and I really miss my 223 .
I have six barrels for my Contender and 3 for my TCR- 87, ain't nearly enough.
Paul G.
Once I was young, now I am old and in between went by way to fast.
The end move in politics is always to pick up a gun.
-- R. Buckminster Fuller
I have 2 Contender frames with 9 barrels all pistols. I also have 3 Encore frames with 8 barrels all rifles.I have about all the barrels that I need unless I run into a good deal on a 45-70 barrel for the Encore when I have money in my pocket..............Terry
I have tc bbl's for every pistol caliber I load except for 44spl along with 10" match 22lr bbl for standing silhouettes.
[IMG][/IMG]
I also use a contender to practice for the free pistol.
[IMG][/IMG]
The extra weight the the extremely heavy 14 ounce trigger on the contender makes it an excellent choice to practice with.
Bbl's are only part of the tc world. Grips, setups, uses of the tc's are only limited by their owners thoughts, ideas, limitations.
I'm down to six barrels and two G-1 frames. I need to get a 357 octagon when I can find one at a good price.
Check out post #14 and see what I did with my Encore with a 7mmBR barrel, and I have another one with a collapsible stock from a M-4.
http://castboolits.gunloads.com/show...5-AR-furniture
Doc that is a nice setup.
Here is what I have for my Encore;
30-06 Rifle blue
45-70 Rifle Stainless (love this barrel)
457 GNR 17" with brake stainless.
50 caliber Muzzle loader.
Handgun Barrel
475 Linebaugh barrel Blue
7mm-08 Blue
Not really enamoured with the 30-06 might sell that one to get another big bore.
My favorite barrels are the 45-70 and 457 GNR both are very accurate.
I just got another mold for my .458 it is hammer of bullet. 460 grains with lube and gas check WFN.
I like those I have the laminated stocks from E Arthur Brown.
Can you PM me the info on these I may just try this setup.
The stocks I installed on my Encore's are also available for the Contender and the G2.
This is the grip that Choate makes, called the M4 Pistol Grip.
http://www.riflestock.com/store/do/product/PGS/09-03-14
You will need the buffer tube for a A2 fixed length with the PRS butt stock like the upper gun.
This is the butt stock I have on the upper rifle in the picture.
https://www.magpul.com/products/prs-...stock-ar15-m16
For the short rifle I installed the same Choate M4 Pistol grip but instead of a short buffer tube for a M4 I installed a KYNSHOT hydraulic shotgun buffer that can reduce the recoil up to 80%. I have a 12 gauge fully rifled shotgun barrel from the custom shop that fits on this frame also which is why I installed it.
http://www.nokick.com/KynShot_Hydrau...kyn-rb5100.htm
You will need the castle nut to hold this to the Choate M4 Pistol Grip.
This is the collapsible Magpul stock that is on the short rifle.
https://www.magpul.com/products/ctr-...stock-mil-spec
This is the Cheek Riser that I installed on the ctr stock it is the .75 height.
https://www.magpul.com/products/ctr-moe-075-cheek-riser
It comes in 3 heights .25, .5, and .75
Excellent and thank you.
I'm down to three barrels 357 max, 44 mag and a 22lr. had a 357 mag, 45-70 and a 22 hornet, the one I wish I had not sold was the hornet, it was a tack driver.
I would gladly trade my 30-06 Encore rifle barrel for a 44 mag barrel.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |