Interest in a 360640 or Some Other 180 RNFP for the .357?

[Greg S]

I'd be interested in a 180gc solid/HP. The other thread fizzled out next page down ( http://castboolits.gunloads.com/show...Cramer-HP-Pins ) Mihec is out of the C358-180. Thanks, Greg

[Greg S]

Bumpety bump for more interest. Lets get the ball rolling for summertime fun and fall hunting seasons.

[wbrco]

Relative beginner here, but I would like something abt 175/180 grains for my 1894, but want it to tumble lube ok. Deep lube grooves don't help me much.

[dragon813gt]

Relative beginner here, but I would like something abt 175/180 grains for my 1894, but want it to tumble lube ok. Deep lube grooves don't help me much.

He already makes the 359640 which is 170 grains. They tumble lube fine w/ the conventional lube groove. I've pushed them w/ a max charge of H110 and 45/45/10 w/ no hint of leading.

[AZBrian]

I'd really (really!) like a 180g Solid/HP. Would love to have Mihec's C358-180-RF in plain base. I put my interest on the other thread but that one doesn't seem to be moving. Count me in for one of those if we can get a rerun. Heck, I think I'd even go for a GC version of the same - so that would be a count me in for two of those!

[rollmyown]

Who made the mold for the original Glen Larsen design?

[outdoorfan]

Not sure, but I think Lee did.

[scotth]

yes it was a custom run from lee. lets get somebody to rerun this one and i am on the list.

[rollmyown]

I could be pretty easily persuaded to go for a Glen Larsen 2 cavity made by either one of our 2 great and prolific mold makers.

[Greg S]

I just Pmd Mihec for a rerun of either the c358 or c360 in a 180. Hopefully he'll see this and the other thread here and start a GB. Fingers crossed boys n girls.

[AZBrian]

Oh please please! Hope he says yes. I have 12 moulds in 358 to 360 but don't have the 180 and would so like to have that one. Oh, but I already said that above. Well, I don't mind saying it again.

[Greg S]

One last try before I go elsewhere. Need a RNFP heavy 170-180 for a levergun.

[imashooter2]

I don't understand the difficulty. They're as common as can be. Take your pick of material, cavities and base:

http://noebulletmolds.com/NV/index.p...h1d7sccr19asj3

http://noebulletmolds.com/NV/index.p...h1d7sccr19asj3

[Greg S]

I know, but the models I'm interested in are out of stock.

[dragon813gt]

Then have Accurate make you what you want.

[Greg S]

Alright Imashooter2 and Dragon813gt, you got me to get registered and start an inventory re-run thread over at noe Forums for a 360-180 RF.


Well, I was looking at the wrong mold so going to kill the thread over on NOE since what I'm looking for is the 360-180 WFN which is in or was available.

[imashooter2]

Look at the 360-180-WFN. What you want appears to be in stock.

[Rattlesnake Charlie]

NOE has listed his 360-180-WFN for several years. I bought a 4-cavity RG from him back in 2012 or 2013.

[Bigslug]

I was pondering that one, but am now stumping to get the GB launched on the NOE/Ranch Dog 175 grain tumble luber to fill that particular niche. I really like the WFN concept, and life has gotten better since I started dialing back the need for a the lube sizer. Heck, if Al runs it with HP pins, I might buy that AND a solid.

I'd be glad if you joined us.

[imashooter2]

Conventional lube groove designs have always shot better for me than microband designs, and they film lube just fine.

Besides, you're going to have to run it through a sizer to seat the check.