What did you do in the reloading room today?

[44Blam]

Finished PCing my Acc 40-180BGs - another 359... So, I've got a few of these guys to load.

[kevin c]

JB Welded some loose mold handles. I thought about pinning them but thought I'd try the lazy man's approach.

We shall see if they can stand the heat in the kitchen...

[cwlongshot]

SORTED BRASS!!!

Not my fav and didnt find any treasures... Well I did find 50 50BMG then 200 ish Fed 38 SPL. Everything else was boring 9mm, 40, 45 & 223. Ooh maybe 60-75 30/06

CW

[cwlongshot]

JB Welded some loose mold handles. I thought about pinning them but thought I'd try the lazy man's approach.

We shall see if they can stand the heat in the kitchen...

I have had great luck with JB. BUT, I also grind the steel so the JB has more surface area to really grab. I have had some going 5 years plus.

https://youtu.be/MkveXm0dNXo

CW

[2A-Jay]

Reloaded 100 .45acp with 230grHornady XTP over 7.5gr AlliantBE-86

[Brassmonkey]

Looked at the press, yep it's there
Looked at the brass, yep plenty of that
Looked at the powder, oh yeah lots of that
Looked at the boolits, gottem
Checked the clock, plenty of time
Now what am I missing?

[Murphy]

Looked at the press, yep it's there
Looked at the brass, yep plenty of that
Looked at the powder, oh yeah lots of that
Looked at the boolits, gottem
Checked the clock, plenty of time
Now what am I missing?

Primers?


Murphy

[Walks]

Did a bit of Mold maintenance.
Checked a bunch of molds to see if Ballistol was still doing it's job.
Set up My L-N-L for .44Mag.

[44Blam]

Powder coated about 350 40 cal boolits intended for 40 S&W. While they were cooking I GC'd (with my homemade gas checks) and resized about 150 40 cal boolits intended for 10mm...

[Dunross]

Built a workbench yesterday for bullet casting work. Had this old rolling steel frame from a color separation machine that's been out in my shop for years. Bought a sheet of 3/4" plywood, cut it to fit, put some bracing in underneath and it's ready to go. Thought I'd use it this weekend, but the weather report is crapping out so maybe I'll just work on the internal shelving. When I'm not casting my lead pot and equipment will be stored underneath and I'll be able to use the work top for other work.

[fatmanunited]

Cast about a hundred Lee 1oz key drive slugs.
The Night Before, I loaded a hundred rounds of 1oz AA target loads for my friends daughter. She is on the H.S. Trap Club, and I figure if I can cut her practice costs down she can practice more for less...
It's all about the next generation....

That is awesome sir

Sent from my SM-G988U using Tapatalk

[Texas by God]

Yesterday I loaded some .308” 125 gr Nosler Ballistic Tips that I found in the bullet drawer in my ultra modern .30 cal cartridge - the .30 Short Flanged Needmoor- AKA 30-30 Winchester.......
They kind of look like .17 HMRs on steroids.

[cwtebay]

Started loading ladder loads for my son's 270 with RL19. Looking forward to shooting them tomorrow.

Sent from my Pixel 5 using Tapatalk

[2A-Jay]

Sorted brass for tomorrows reloading of Milsurp 30-36 cases (loading to M2Ball specs.

[44Blam]

Loaded part #3 of my Accurate 40-180BG 10mm odyssey. Part 3 is 18 boolits in an effort to fine tune my load.
Then I resized about 400 boolits that are intended for my 40 S&W loads.

[Soundguy]

Loaded up 124 grain cast lead round nose over a tight group

[44Blam]

Tested more 10mm... Got some good #s with good accuracy:
Stats - Average 1302.38
Stats - Highest 1319.39
Stats - Lowest 1294.46
Stats - Ext. Spread 24.93
Stats - Std. Dev 9.3

It is AA#9 with a gas check Accurate 40-180 BG (with home made gas checks) boolit that was powder coated. It was fairly "warm" recoil wise, but pretty darn accurate...

[onelight]

Loaded 550 9mm on the auto breechlock pro with some BE-86 and 125 grain Hi-Tek RN

[cwlongshot]

Im going back on the RCBS press with the NOE gas check seated installed. I have a few hundred LEE 312-155 and Lyman 314299 cast to seat checks upon.

CW

[JoeJames]

Too cold to do any reloading, but melted down some loose wheel weights into ingots. After skimming off the clips got about 5 1/2 pounds. Fluxed with clean sawdust.