What did you do in the reloading room today?

[jdfoxinc]

Sized the last of the .380 ACP brass. Now to prime 500.

[cwlongshot]

Got a batch of 7MM Rem Mags ready to load for test Saturday.

The rifle is gonna be a rechamber/re barrel project. But might as well see ifnit shoots!! ������

CW

[McFred]

I'm starting work on some cedar handles for some HSS LR/SR primer pocket reamers I picked up the other day. Getting the cedar trimmed down to 1-3/8" diameter and assembling the hardware I intend to use is as far as I got today.

[McFred]

Converted, trimmed/deburred and cleaned 185 30 carbine to 5.7 Johnson Spitfire. No wrinkles or lube dents-nickle plated even. Can't explain how that happened.

Those look awfully familiar Newtire! I've been helping a buddy with his 5.7 Spitfire Kurz boltgun project:



They just need to be trimmed and neck-turned. What are you feeding them through, Newtire, an M1 or something else?

[Michael J. Spangler]

Loaded a couple of these. 358156. 50/50 alloy.
C Blue lube
3.5 grains bullseye.

[lightman]

In the shop not the loading room. Started stamping identifying letters on a 3000# pile of wheel weight ingots. Probably about half through.

[Walks]

Loaded about 300 .44MAG Cowboy Loads.

Finally set up the 1st set of HORNADY L-N-L bushings for those dies. Set up the dies for .44SPL, then used the REDDING .44 cal spacer washers to raise the dies up to load .44MAG. Those washers for .44 & .38/357 are fantastic.
Do the .38/357 next.

[The Governor]

I loaded some cast.45 ACP lubed with Johnson's Paste Wax for the first time.

[KrakenFan69]

Hi-Tek Coated 1,000 Lee 401-175 TC to add to the horde. I think I have around 5,000 ready to load now.

Kraken Fan #69

[jdfoxinc]

Started depriming 800 + 16 ga compression formed hulls.

[trixter]

Turned the light off. (I wanted to stay long bur work beckoned.)

[DxieLandMan]

Powder coated, sized and loaded 100+ rounds of .41 Magnum.

[cwlongshot]

Loaded up 20 7MM RM rounds for testing after the Monsoons forcast for tomorrow...

CW

[Tom W.]

Sorted and trimmed 30/30 brass. The Winchester brass is now trimmed, but still have a pile if R-P and Federal brass to trim.....but that will be later....Did I ever say that I HATED to trim brass?

[jonp]

Load and test some Acme 100gr RNFP in my Ruger 32H&R Mag's. I used Unique at 2.5gr and they were well under the expected velocity. Going to bump them up some and see what happens as the recoil was very light. I did crimp them long in the groove so that may be the answer to why they were slower than expected.

Almost forgot, one of my bosses gave me a Folgers Coffee Can full of .40 Brass and most of a pound of Power Pistol. I am tumbling the brass now.

[Ironnewt]

Worked with my Redding Turret press and a universal decapping die. De-capped about 100 pieces of .300 Blackout brass. Going to clean them tomorrow, load them Monday.

[mac60]

Converted 277 pcs. of 5.56 LC into .222 Rem. for my Savage 340, resized 1,000 pcs. 9mm. 'Bout wore me out.

[wendyj]

Melted about 800 bullets I no longer shoot and casted about 200 45-70s. Loaded up about 50 rounds of 357 to shoot a little tomorrow.

[Tom W.]

Flared my Winchester 30/30 brass , so now it's ready to load. I have a LOT to prime and load. It will keep me busy for a while. My Federal and RP brass went back into storage.

[fralic76]

Finally got around to size and gas check 450 113gr 30 caliber bullets. Next to powder coat. Also did a little cleaning and organizing of the reloading bench.

Sent from my SM-G955W using Tapatalk