What did you do in the reloading room today?

[jdfoxinc]

De bulged the first of 1k .40 S&W.

[chieffan]

Started to clean up an old Lyman 45 Lub/Sizer. Old dried out lube from not being used in many years I am sure.

[RedlegEd]

Teaching my daughter how to reload, so we loaded up 100 rounds of .45 ACP 200gr SWC over 4gr Bullseye for her to shoot in her Kimber CCII.
Attachment 217490

[Texas by God]

I'm converting an old fl 8x57mm die to a trim die.

Sent from my SAMSUNG-SM-G930A using Tapatalk

[Walks]

I ran 300 #429667 thru my old Lube-Sizer. .430dia with White Label BAC.

[robg]

Loaded up 40 45-70 with 20 grains of 2400 some with a wad of toilet paper some without .see if it makes any difference to accuracy.

[jdfoxinc]

Continued debulging .40 brass. This is bought from a range. Lots of .40s with oversized chambers. Some with very tight chambers, (No buldge).

[mdi]

I'm starting on my "Just in case" stash of 9mm. I have a jug nearly full of 45 ACP ammo that works quite well in my 2, 45 ACP pistols and is a known performer (mebbe 350 rounds) that's handy to grab if I need them "just in case". I'm starting on a bunch of 9mm ammo that will work in my 3, 9mm pistols that performs good and feeds reliably in my 3 pistols. I have about 150 so far, mixed brass, CCI sm pistol primers with a medium-high load of Universal. I have fired this load out of my Ruger LC9s into water jugs and got penetration through 3 jugs and entered the 4th. Clocked at 1075 from the short barreled Ruger and got 3" groups, rested in hand, at 10 yards. Recovered bullets showed good expansion to 3/4". I'm sure this load will work well in any 9mm pistol, and if I have to evacuate (nearly had to due to forest fires last summer) I can just grab my "9mm Bag" that has 2 pistols and about 200 rounds (so far). I was never a Boy Scout, but I believe in "Be Prepared"...

[EMC45]

Loaded a box of 452-374s over Bullseye yesterday. Shot them today. Started really accurate which diminished quickly. I read the notes I had and they said "leaded". Not a fan of this bullet. I spent some elbow grease getting the streaks of lead out of my 1911 barrel.

[Chev. William]

Last three Days have been suitable for work outside in my Reloading shop (back patio) so I have 300 5.7x28mm cases three Steps into reforming to .278" body diameter for my Wildcat .25ACP/.25Stevens long derivatives. One more swaging step and then the trimming, flash hole drilling and deburring to go to finish this batch.

[Bookworm]

Pulled down 120 rounds of 7.62x54R surplus ammo. Adjusted powder charge down, and reassembled.
Roughly 2275 fps with steel jacketed Russian surplus. Feels like shooting a light .30-30 load.

[AndFereira]

Wet tumbled a batch of .45 ACP.

[evoevil]

Made gas checks ..... getting ready for my new MP mold,...... hoping it will be here this weekend

[DxieLandMan]

Loaded 25 rounds of .577 Snider. 62.5 grains FFFG is a pleasant load to shoot.

[wolf3006]

Made a few tool post.

[Tom W.]

Loaded a box of 9 mm, then lubed and sized a bunch with my Lee push through sizer and JPW. Probably gonna dip the boolits in some mule snot if I can find some mineral spirits to thin it with.

[JBinMN]

45/45/10 lubed 50 - 158gr SWCs, sized them .358 & re lubed them getting ready for some .357M ladder test loading with Red Dot at 5.0/5.1/5.2/5.3/5.4. later today. Next is 50 - 148gr DEWCs that I will start the process when I start loading the SWCs.

[MOA]

Made a few tool post.

Great looking tool posts there wolf.

[wolf3006]

Thanks MOA

[greenwart]

Cast Peanut butter jar of Lee 401-175-TC. I am only going to buy 6 cavity mold from Lee in the future. Switching between 2 cavity and 6 the quality difference is worth the extra $15. Plus you can cast mountains of bullets.