What did you do in the reloading room today?

[whisler]

Stocked my primer shelf.

[waco]

Boiled and cleaned the 450 for a new batch of Glen's Black lube. Loaded 20 308 rounds to test with new lube. also loaded 100 rounds of 38spl with the new stuff.

[hc18flyer]

Spent the day casting 358 win and 8 x 57 hunting boolets, all sized and lubed too. I also cast a bunch of Lee 324-175''s for my brother''s Yugo M-24/47. Ran myself out of 8mm gas checks. Should be good till Spring. It was a crappy, wet day, perfect to stay in and cast. Next weekend scouting for deer season, and cutting firewood. Flyer

[MDC]

Cast a batch of MP 45acp

[WFO2]

Nice Boolit Buddy what mold is that . Weight Etc .

[MDC]

Nice Boolit Buddy what mold is that . Weight Etc .

They are from Mihec's 454-200 mold. Cast from coww+ 2% Sn they come out at 198gr. I cast these from 8lb range scrap 2lb coww + 2% Sn. I haven't weighed them yet but they should be a tad heavier

[DerekP Houston]

switched the LnL over to 9mm dies and plate and sent a batch through with the new 38 S&W expander plug inserted. Bullets seated much easier hope no leading on my next trip. had to seat them a bit deeper for it to cycle through my semiauto though. titegroup 3.9gr .34 disk load.

[robg]

Loaded 100 rounds of 308 160 gr rngc boolits with 18 gr of 2400.

[marlin39a]

Took a close look at my supplies. Ordered an 8# jug of Hodgdon HP-38, and an 8# of Hodgdon CFE-223. I'm good now in case of the Hildabeast.

[taco650]

switched the LnL over to 9mm dies and plate and sent a batch through with the new 38 S&W expander plug inserted. Bullets seated much easier hope no leading on my next trip. had to seat them a bit deeper for it to cycle through my semiauto though. titegroup 3.9gr .34 disk load.

What boolit is that?

[DerekP Houston]

What boolit is that?

Some left overs I had from a mold I sold. Rcbs 124gr tc

[Texas by God]

Loaded my first batch of .40 S&W. Berrys 180gr plated HP over 6grs Unique. Function fired 3 rds into the water trough- I'll fish them out tomorrow and check for expansion- like I care. I got my Lee mold the other day; just waiting for casting weather! Best, Thomas.

[Reverend Al]

Pulled down some old junk ammo for the components, sorted some brass, full length sized and deprimed about 200 rounds of .270 Winchester brass ...

[Tom W.]

Had trouble getting in. I had the dealer replace the door and now the lock is sticky I put a shot of RemOil in it and am letting it soak while I go get a CT scan........

[WFO2]

Hope your scan turns out good .

[Jal5]

Ran some 223 yesterday with my grandson as helper. Fun. Lots of questions. Need to inventory my powder and primers and make a large purchase for future needs.

[shoot-n-lead]

Hope your scan turns out good .

X 2

Prayer sent for a good report.

[DerekP Houston]

Some left overs I had from a mold I sold. Rcbs 124gr tc

very disappointing results. over half failed to fire, solid primer strikes and nothing on the 2nd pull either. Perhaps my lc9s doesn't like S&B primers, but it shot the rest of the ones I loaded with plated bullets fine. This was the first attempt loading 9mm on the progressive though, perhaps I messed something up.

[Reverend Al]

Cleaned some more '06 brass today ... and will go down to the shop and anneal it tomorrow. Then I have to get out guns, ammo and accessories for a range day on Thursday!

[flyingmonkey35]

very disappointing results. over half failed to fire, solid primer strikes and nothing on the 2nd pull either. Perhaps my lc9s doesn't like S&B primers, but it shot the rest of the ones I loaded with plated bullets fine. This was the first attempt loading 9mm on the progressive though, perhaps I messed something up.

I had the same issue with a highpoint carbine. Found the firing pin spring was too weak for s&b. As they all fierd fine in a different gun.

The lc9 is a small gun

Sent from my LGLS991 using Tapatalk