What did you do in the reloading room today?

[EMC45]

Loaded 10 Lyman 225-415s over 7gr. Red Dot and 10 Speer 52gr. HPs over H4895.

[KrakenFan69]

Loaded up 1,200 Hi-Tek coated Lee 401-175 TC for my Glock 35 for a match this weekend. Now to load 9mm for my son's Glock 17.

Kraken Fan #69

[Bookworm]

Just got my K&M Neck Turning tools in. Tried them out on 82 pieces of 7.62x54R.

Annealed, full-length re-sized, length trimmed, prepped necks, trued necks, tumbled.

If this works, I've got 150 brand new PPU cases, and about 250 various used brass to process.....

[Reverend Al]

Went down to the shop, but didn't do any reloading today. Instead I sorted, priced, and boxed up some surplus items to put on my table at the local gun show this Sunday. Will take 6 or 7 guns along too just to see if people are buying. At most of our previous gun shows people seemed to be buying small and relatively inexpensive "trinkets" (dies, brass, bullets, moulds, etc.) but not so much the big ticket items like guns ...

[skeettx]

Yesterday, shot a bunch of home made shot at the skeet range
Today, Loaded a bunch of 6x47 Remington, and some 35-300 Rum ammo
T'will shoot some of it tomorrow.

Mike

[Tom W.]

Sized and lubed more 9mm boolits. I was going to cast, but even w/ the a/c on it was a bit warm in the shed....

[Hotrod99]

Been raining everyday for 2 weeks... so no shooting.... but I found time to make my first blend and cast a few 200gr 45acp.

Also melt and made ingot of pewter... about 7.5lbs!

[62chevy]

Sized and lubed more 9mm boolits. I was going to cast, but even w/ the a/c on it was a bit warm in the shed....

Capt. I need more insulation. But Tom we have to go light speed to sector lows and that could take 2 hours if ya don't get warp speed working.

[Tom W.]

I'm retired now... no hurries here. It would be nice if I put some ceiling insulation in the shed. Sometimes I go in the evening when it's a bit cooler ( a relative term here in Alabama) and cast a few hundred.....

[robg]

Loaded 50 45-70 s 415 gr. Boolits over 20 gr 2400.fitted a rifle basic trigger in my savage 116 ,then to please my wife fitted a new nozzel on the kitchen tap .range tomorrow .

[dbmjr1]

Loaded 50 .32WCF and 100 .38spl.

[Soundguy]

Nice pewter ingots!

[ThomR]

I loaded a bunch of 380 for my wife's pistol and started priming 9mm cases. I ran out of small pistol primers, now I need to see if the small rifle primers I have will work.

[marshall623]

Working on some 7 TCU 's newly formed cases out of Mil. Spec. range pick up's .
160 Lyman 287461
Sized 285" over 20.2 gr. of RL 7 . Will finsh after Church .

Sent from my SM-G930V using Tapatalk

[Minerat]

Finished converting 40 - 30 06 cases to 8mmx57, and polishing.

[Tom W.]

I loaded a bunch of 380 for my wife's pistol and started priming 9mm cases. I ran out of small pistol primers, now I need to see if the small rifle primers I have will work.

I loaded 100 9mm w/srp. Haven't been to shoot them yet, but I'm pretty sure that they will work. Seated just fine. I believe somewhere on this forum that there is a thread about it.

[cwlongshot]

I have been cleaning brass... I bought a large quantity of 40 Brass form a couple sources and they needed cleaning.

Then I loaded up four ladder loadings for my 6.5 Grendel that I shot last Sunday.

Then I have been sizing 40cal powder coated bullets.

CW

[rmark]

Cast a whole bunch of .30, .38, .45 caliber bullets since it was cooler due to the overnight rain.

[David2011]

Cast some 158 gr rnfp and powder coated ‘em red. Loaded ‘em into highly polished brass for a cowboy shoot. Looked like a batch of lipstick.

[EMC45]

Loaded 50 round of 9MM - 120gr. Lee TC sized to .358 over 3.5gr. Titegroup.