Lather rinse repeat.
Lather rinse repeat.
Maybe not this exact tool but something similar might help. I've got one bc of a bad knee.
https://www.amazon.com/Folding-Helpi.../dp/B0002VUQPG
Sent from my iPhone using Tapatalk
My Feedback thread:
http://castboolits.gunloads.com/showthread.php?249515-prsman23
Yep,got me one of those"pickup sticks"works really well.Can even pick up a piece of paper with mine.Got mine at the local pharmacy,was $19.95 but is of good quality.Oh yeah,for getting up off the floor,you could always hang a block and tackle from the ceiling.
Good luck.Have fun.Be safe.
Leo
People never lie so much as after a hunt,during a war,or before an election.
Otto von Bismarck
I have those garage cushions that interlock, unfortunately I didn't have one in that space, but I should add more. I don't mind being on the floor sometimes, it's just the decision to stand up that complicates things. Block and tackle affair sounds like the best answer....
-Mike
a m e r i c a n p r a v d a
Be a Patriot . . . expose their lies!
“In a time of deceit, telling the truth is a revolutionary act.” G. Orwell
Just finished resizing a bunch of 9mm brass. Sorted the commercial from the military and starting to swage prime pockets. Just put a load in the tumbler. Trying to do a bunch of tumbling this summer to utilize the hot summer sun for drying.
Last week my usual load of 18gr of 2400 behind a 160 gr boolits wouldn't shoot worth a damm 3 inch at 100 yards instead of 1.5 inches .so I've sized trimmed etc loaded up 20 rounds with 17/17.5/18/18.5/19 gr of 2400 I hope one of them will get back to shooting as it was .now to clean the barrel ,hope this solves the problem.
Resized another 200 or so pieces of 308 brass. Still have a gallon and a half to go.
And then I have to ream, uniform, and trim them.
I'm done buying once fired military 308 brass. I swear!
Loaded 250 12 gauge shells with home-made shot
What fun, what fun
Mike
NRA Benefactor 2004 USAF RET 1971-95
Loaded and shot the 58 ML with 100 grans of powder under a 500 gr minie, big push on my shoulder, I likie a lot.
Also my 12ga ML, used the shot I made. This is fun to shoot shot I make.
Je suis Charlie
ΔΕΞΑΙ
Rednecks run the Brits out of this country years ago,
I will defend this country from anyone or thing that tries to take it from me or mine
I AM A REDNECK!!!
"If ever a time should come, when vain and aspiring men shall possess the highest seats in Government,our country will stand in need of its experienced patriots to prevent its ruin." Samuel Adams, 1776
I had to try out my new NOE 460-405 mold. Cast about 200. They were about 390 gr, water dropped, bhn 15. Plan on driving them about 1400-1500 in Marlin .
LGS has a Taylor n Co 45-70, 32 in barrel. Can't swing the 1200 bucks. Maybe if it's there next month?
Cast 90 x190g x 358 sil boolits & 90 x150gr x 309fn boolits .lubed sized gas checked relubed .would have been more but my wrists started to give me some stick so I had to call it a day .club is shut next week so its time to stock up .
Loaded 100 158gr. RNFPs in .38 Special cases over 3gr. Bullseye.......................................... yesterday
You can miss fast & you can miss a lot, but only hits count.
Didn't do any reloading but did empty a couple of boxes of 9mm and 45acp that I cast and reloaded
I'm a Red Cross blood donor- are you? Make an appointment to donate today http://www.redcrossblood.org/make-donation
http://www.redcrossblood.org/
FOR Disaster Relief DONATIONS-
http://http://www.redcross.org/charitable-donations
prepping some 303 brit brass for snake shot loads
Thanks, soundguy, guess yesterday was my day, got the shelf finished and installed then my neighbor called and asked if I wanted a reloading press he found. [He breaks into houses for a living (works for the mortgage companies maintaining and cleaning forclosed properties). A couple drops of KROIL and it 's smooth as butter.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |