What did you do in the reloading room today?

[jdfoxinc]

Lather rinse repeat.

[prsman23]

I did that yesterday. Knocked a bin of 45 tumble lubed slugs on the floor. Had to move a shelf to get to them and get on my hands and knees to gather them up. When I went to stand up, I didn't think my knees were going to make it, so I had to find something to grab. Thought I might be there when my wife came home... sad, but true...

Maybe not this exact tool but something similar might help. I've got one bc of a bad knee.
https://www.amazon.com/Folding-Helpi.../dp/B0002VUQPG


Sent from my iPhone using Tapatalk

[woodbutcher]

Yep,got me one of those"pickup sticks"works really well.Can even pick up a piece of paper with mine.Got mine at the local pharmacy,was $19.95 but is of good quality.Oh yeah,for getting up off the floor,you could always hang a block and tackle from the ceiling.
Good luck.Have fun.Be safe.
Leo

[Bob in St. Louis]

Magnets on a stick work for primers too.

[tucumcari_kid]

I keep a scrap cut of carpet in the garage for when I feel like going 'primer hunting'...whatta sport! And yep...somedays have to climb up the side of something to straighten out those knees!

I have those garage cushions that interlock, unfortunately I didn't have one in that space, but I should add more. I don't mind being on the floor sometimes, it's just the decision to stand up that complicates things. Block and tackle affair sounds like the best answer....

[OS OK]

I have those garage cushions that interlock, unfortunately I didn't have one in that space, but I should add more. I don't mind being on the floor sometimes, it's just the decision to stand up that complicates things. Block and tackle affair sounds like the best answer....

Yeah...for me though...when I get a package of primers out, I say out loud (so I'll pay attention)..."Hey Dummie...these are primers, you know, like 'Mexican Jumping Bean' kinda primers...pay attention!"
Still though, I'll have a few escapees from time to time!

[lightman]

Just finished resizing a bunch of 9mm brass. Sorted the commercial from the military and starting to swage prime pockets. Just put a load in the tumbler. Trying to do a bunch of tumbling this summer to utilize the hot summer sun for drying.

[robg]

Last week my usual load of 18gr of 2400 behind a 160 gr boolits wouldn't shoot worth a damm 3 inch at 100 yards instead of 1.5 inches .so I've sized trimmed etc loaded up 20 rounds with 17/17.5/18/18.5/19 gr of 2400 I hope one of them will get back to shooting as it was .now to clean the barrel ,hope this solves the problem.

[308Jeff]

Resized another 200 or so pieces of 308 brass. Still have a gallon and a half to go.

And then I have to ream, uniform, and trim them.

I'm done buying once fired military 308 brass. I swear!

[skeettx]

Loaded 250 12 gauge shells with home-made shot
What fun, what fun
Mike

[RED333]

Loaded and shot the 58 ML with 100 grans of powder under a 500 gr minie, big push on my shoulder, I likie a lot.
Also my 12ga ML, used the shot I made. This is fun to shoot shot I make.

[shell70634]

I had to try out my new NOE 460-405 mold. Cast about 200. They were about 390 gr, water dropped, bhn 15. Plan on driving them about 1400-1500 in Marlin .
LGS has a Taylor n Co 45-70, 32 in barrel. Can't swing the 1200 bucks. Maybe if it's there next month?

[Grmps]

Finished and installed another shelf unit to store coated bullets on

[robg]

Cast 90 x190g x 358 sil boolits & 90 x150gr x 309fn boolits .lubed sized gas checked relubed .would have been more but my wrists started to give me some stick so I had to call it a day .club is shut next week so its time to stock up .

[EMC45]

Loaded 100 158gr. RNFPs in .38 Special cases over 3gr. Bullseye.......................................... yesterday

[Jal5]

Didn't do any reloading but did empty a couple of boxes of 9mm and 45acp that I cast and reloaded

[Retumbo]

I processed some bees wax and pine tar

[triggerhappy243]

prepping some 303 brit brass for snake shot loads

[Soundguy]

Finished and installed another shelf unit to store coated bullets on

Very nice. Never can have too many shelves

[Grmps]

Thanks, soundguy, guess yesterday was my day, got the shelf finished and installed then my neighbor called and asked if I wanted a reloading press he found. [He breaks into houses for a living (works for the mortgage companies maintaining and cleaning forclosed properties). A couple drops of KROIL and it 's smooth as butter.