VS - Hi Quality Powdercoating Powder For sale

[Smoke4320]

I could get to 1900-2000 depending on Caliber (the larger the caliber the faster I could get)
after that I had to add checks to retain accuracy

[Smoke4320]

Translucent copper finally arrived .. It was on the dragons tail too.. 318 curves in 11 miles ..
all copper back order will ship in the morning !

thanks for your patience

[Smoke4320]

Fresh shipment of Clear PC should be arriving Friday/Monday

Please get your orders in … I will ship in same order as received


Thanks

[Smoke4320]

OK on top of Fresh shipment of Clear Arriving Friday/Monday looks like Flame Red will Arrive Tueday or Wednesday
Please get your orders in … I will ship in same order as received


Thanks

[Smoke4320]

Clear PC is back in stock ..All backorders shipping tomorrow

[Smoke4320]

Flame red is back in stock
All backorders shipping out today

Thanks

[Smoke4320]

Jet Black PC should be back in stock Wed or Thursday
so get your orders in.. I ship in order received

Thanks

[Smoke4320]

Jet Black is back in stock and all backorders shipping today

Thanks

[reddog81]

What's the status of the Translucent Copper?

[Smoke4320]

TL copper is in stock right now
I do my best to keep the first post on thread updated

[Mjdd23]

Did a small batch with the Windowshade Gray which was the half pound free for the Black Friday deal. Covers really nice and looks good. It was 50 degrees and raining here when I tumbled these and they coated well. Smash tested fine. 400 degrees for 20 minutes. Thanks Smoke!
Mark

[Smoke4320]

Those look real good .. Thanks for posting (and the purchase )

[Smoke4320]

Fresh shipment of carolina blue and signal blue should be arriving Thurs/Fri so get your orders in
Thanks

[Smoke4320]

Carolina blue and signal blue are back in stock
All backorders shipping out by tomorrow

[T_McD]

Smoke, any changes in your application method? Been a few years just curious if techniques have evolved any

[Smoke4320]

people have developed various ways to do this depending on THEIR environmental conditions .
here in the south with very hi humidity most of the year I still do it this way
Pre heat Convection oven to 400 degrees

The way I Dry Tumble is to get a plastic container with snap on lid that has a triangle and #5 stamped on the bottom (this is VERY important to get acceptable static) I have gone to using Ziplock S Round (2 cup) twist lock containers (Rubbermaid equilavent will NOT holdup) , Others use cool whip containers
add enough BLACK 25 gram Airsoft BB's top cover about 1/2" deep on bottom .. (2 to 3 layers deep)
add 1 teaspoon of powder for cool whip containers (for the first load ONLY). 1/2 teaspoon is more than enough for S Round Containers
add 50 to 100 bullets . The smaller ones like 223 would be 100 larger like 45 ACP 230's might only be 30 at a time
snap on lid and swirl the container to the count of 30 then shake fairly hard up and down to the count of 30
lift lid, Pick up bullets one at a time with long needle nose pliers .. Tap pliers on container edge to shake off excess powder back into container
Just started doing this with double layered bowls glued together
Speed up process, knocks off excess powder so you don’t have to tap bullets on container, and leave just the bullets in the bowl for easy pickings
http://castboolits.gunloads.com/show...-from-the-BB-s

Put bullets on cookie sheet lined with Non stick foil (will last many many cycles)
Put in oven for 15 minutes . pull out let cool and put in a bullet box

Oven .. You need to be sure what temp the Oven is actually cooking at... your aim is between 375 and 400 degrees
Oven needs to be preheated before putting bullets in .. I found my oven take approx. 8 minutes to reach 380 degrees
do a few small batches say 10 bullets till you find what temp YOUR over gives a nice even flow to the powder.. too cool and you get clumps.. to hot and you get nice looking colored clumps melted lead puddles..
a convection oven with a fan to distribute the heat evenly throughout the oven will give you an almost sprayed slick look..

Blue Nitrile gloves can be used to pick up bullets .. So far other gloves have proven to not work ( they will remove powder everywhere the gloves touch )
Or you can always buy a Harbor Freight Electrostatic PC gun for about 59.00 on sale.. This will give you the smoothest finish.. just more setup and cleanup time

NOTE:
At Extreme Hi Velocities you may get black streaking. It the PC Coating smearing .. The only product we have found to clean this quickly and easily is BORE TECH ELIMINATOR

[Smoke4320]

USPS massive price increase effective Jan 27th 2019

I will have to adjust my prices to reflect this increase

Might want to get your powder orders in real soon
Express Size Price
Flat Rate Envelope 12-1/2" x 9-1/2" $25.50
Legal Flat Rate Envelope 15" x 9-1/2" 25.70
Padded Flat Rate Envelope 12-1/2" x 9-1/2" 26.20

Priority Mail Size Price
Flat Rate Envelope 12-1/2" x 9-1/2" or smaller $7.35
Legal Flat Rate Envelope 15" x 9-1/2" $7.65
Padded Flat Rate Envelope 12-1/2" x 9-1/2" $8.00
Small Flat Rate Box 8-5/8" x 5-3/8" x 1-5/8" Inside
8-11/16" x 5-7/16" x 1-3/4" Outside. $7.90
Medium Flat Rate Boxes 11" x 8-1/2" x 5-1/2" Inside
11-1/4" x 8-3/4" x 6" Outside
13-5/8" x 11-7/8" x 3-3/8" Inside
14" x 12" x 3-1/2" Outside $14.35
Large Flat Rate Boxes 12" x 12" x 5-1/2" Inside
12-1/4" x 12-1/4" x 6" Outside
23-11/16" x 11-3/4" x 3" Inside
24-1/16" x 11-7/8" x 3-1/8" Outside $19.95

APO/FPO/DPO Flat Rate Box 12" x 12" x 5-1/2" Inside
12-1/4" x 12-1/4" x 6" Outside $18.45
1. Packaging only available at USPS.com.

[T_McD]

Pm sent

[Smoke4320]

Inventory updated
Stock selling very quickly and doing my best to get restocked soon

[Smoke4320]

New Pricing as of the 1/27/19 because of USPS price increase
1 LB Shipped in the USA is $22.75 (That's powder AND shipping included in the USA)
2 Lbs Shipped USA is $36.75
3 Lbs Shipped USA is $50.75
4 Lbs Shipped USA is $64.75 That's just $16.19 SHIPPED per LB
for quantities over 4LBs Just add $14.00 per LB to cover powder and additional shipping