MiHec 9 mm 147 HP or 155 Solid 4 cav brass for alternativ coating

[Balta]

Can you please inquire about the extra pin set? For speed shooting competitions, the round nose is essential for fast reloads with a revolver. There is an increasing number of people using .38 Short Colt and the new 9mm revolvers (S&W 986 and 929).

It was said that there would be no round nose for the Mihec 230gn .45 HP-bullet, but everyone that ordered "all pins" got pins with a round nose cavity. I stood there with a long nose wondering why I ordered a no HP version when I could have had it all if I did.

Whistler,i have answer from Miha and sorry that option is not possible for this mold,it require different cutter..

[Balta]

Bump...

[alha]

I'll take one each of the 356,.357,.358, .359 sizes, with all pins for each.

snowserver (a*t) hotmail DOT com

[cs86]

Can you please inquire about the extra pin set? For speed shooting competitions, the round nose is essential for fast reloads with a revolver. There is an increasing number of people using .38 Short Colt and the new 9mm revolvers (S&W 986 and 929).

It was said that there would be no round nose for the Mihec 230gn .45 HP-bullet, but everyone that ordered "all pins" got pins with a round nose cavity. I stood there with a long nose wondering why I ordered a no HP version when I could have had it all if I did.

The only round nose pin option that I've seen Mihec provide for the 45 was for the 452374 (I think that number is right...). At the time it was experimental, which makes me believe that he doesn't do that often or it was a first. I did buy the mold and sold it later to create funds for a different style of bullet. I tried the round nose pin and wasn't as pleased with the outcome of lines and fins. I didn't spend much time with the mold either though, which probably has a lot to do with the outcome of the bullet. If you are truly looking for a round nose bullet I would stay with a solid mold without the extra pins. Just my thoughts.

[Balta]

Sign up list updated!

[just_shooter]

I've never used that heavy boolit (155gr.). I'm not sure if it's for revolvers only, or for 9mm pistol as well. Any ideas? I'm looking for new mold for my CZ Shadow, and if 155gr. will work on my pistol I'd buy 2 x SOLID both in .357

[Balta]

sign up list updated!!

[just_shooter]

How about that value shown in red on the picture? That's important because with so heavy boolit it's gonna be tight fit in the chamber. Hope about .35 inch. like in the other project for 135/125 gr No Lube Grove mold GB. This has to be enough I suppose.

[jeremiah.allen1]

I would like a 4 cavity 357-147-HP jeremiah dot allen1553 at Gmail dot com

[Balta]

How about that value shown in red on the picture? That's important because with so heavy boolit it's gonna be tight fit in the chamber. Hope about .35 inch. like in the other project for 135/125 gr No Lube Grove mold GB. This has to be enough I suppose.

Need to chek that to be sure..but it is under 9 mm!

[just_shooter]

Would be helpful information. Just to be sure. Thank you.

[jeremiah.allen1]

I would like to change my diameter to .358

[just_shooter]

C'mon it's time to close this GB, isn't it?

[Balta]

There is not enough orders of HP mold .Have spoken with Miha and ...This GB wil be open to end of September ,as final GB end time.

[BMKoenig]

I'll take a .357 hollow point. rommelbmk (at) comcast.net

[Balta]

I'll take a .357 hollow point. rommelbmk (at) comcast.net

[Balta]

THIS GB IS UPDATED,THIS MOLD IS ALSO AVAILABLE IN 147 grain SOLID only version ,bullet with FLAT BASE.
Yeeee,this can be made with same tool

[worker]

will take a 4 cavity 357-147-HP

pls PM me when/where I need to pay. thx

[Balta]

will take a 4 cavity 357-147-HP

pls PM me when/where I need to pay. thx

You will recive paypal invoice when production start,need your email,you can send it to me by PM..

[just_shooter]

...This GB wil be open to end of September ,as final GB end time.

Hate when the rules are changing during the game. Don't get me wrong I can wait even a year, but have to know that from the very beginning. So, sorry but I'm out of this GB. Please, sign me out.