MATT
****see post #18....stop scratching..... the itch is less likely to fester that way.
MATT
****see post #18....stop scratching..... the itch is less likely to fester that way.
Last edited by 357maximum; 04-30-2014 at 12:46 PM. Reason: revised
Last edited by Dutch4122; 05-01-2014 at 05:31 AM.
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
Matt,
Thanks! As soon as I get a copy of the reamer drawing I'll have more to go on.
Regards,
Tony
Bump to top.
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
I would like:
1- a 2 cav gc option 2 aluminum
2- a 2 cav gc option 4 aluminum
That would be 2 molds, aluminum, gc
Thank You.
Update: I just today received an order of 2,000 Gator gas checks from Blammer. Just mic'd a dozen and they measure a very consistant .289" diameter; and snap nice and tight onto the shank of some BRP 287641 Improved boolits I cast last week.
I would definitely recommend the Gator checks over Hornady checks.
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
I would like an aluminum mold, option 3 please.
Are these mold dimensions calculated for a specific alloy? I use wheel weights, not Lyman #2.
Thanks in advance.
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
Sorry, two cavities.
And thanks for the info.
Bump to the top!
Edd
Charter member Michigan liars club!
"The strongest reason for the people to retain the right to keep and bear arms is, as a last resort, to protect themselves against tyranny in Government." -- Thomas Jefferson
"Consider the clown(s) just one of God's little nettles in the woods, don't let it detract from the beauty. Sooner or latter you are going to run into the nettles regardless of how careful you are."
Beware of man who types much, but says nothing.
Update: I just received this PM message from Josh at A.C.E.
"........ i am now offering a "blank" lyman type nose punch with all molds for $5 they get filled with epoxy (like JB weld) and a vasolined nose bullet fits inside................................. I can also offer a flat punch if you desire for your buy............."
So, if anybody wants the "blank" style Lyman/RCBS nose punch or a flat nose punch ordered with their mold just post here on this thread. I will update your order accordingly.
Last edited by Dutch4122; 05-15-2014 at 12:12 AM.
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
BTT
Last edited by Dutch4122; 05-16-2014 at 10:48 PM.
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
Add me please, measurements to follow.
Thanks!
Randy
Gotcha, and thanks Randy. We'll get that 1908 Brazilian Short Rifle of yours slugged & pin gauged at Edd's place in a couple of weeks.
That makes 14 molds spoken for and several members that committed on the interest thread who have not confirmed their intent to order yet.
Looking good!
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
I have three different 7x57's but have no pin gauge. I'll try to sort them out to find my most likely setup.
I'm most interested in a mould for my rolling block, so...
I'll have to go for the economy model - funds are limited.
Thanks
Merle Morrison
Mercer County, PA
RETIRED
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
I want one of each of these!
Option #1) .287" bands / .276" nose
Option #2) .289" bands / .278" nose
Option #3) .291" bands / .280" nose
Option #4) .293" bands / .282" nose
Please make each one a Steel:
2 cavity = $100.00
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |