MiHec 300 ACC Blackout 2 or 4 Cavity Brass Cramer HP, GC or PB

[Sticky]

Love to be in on this!!

4 cavity PB with all pins

igluit4u at gmail dot com

I know I'm a newbie posting here, but long time lurker and I have one of Miha's awesome 45 moulds, my blackout is hungry for more subs!!

[AJ Peacock]

one 4 cavity PB w/ all pins (including blanks)

Set of handles if that is possible too.

don_peacock (@t) hotmail (d0t) com


Thanks,
AJ

[MTtimberline]

I do not look for how long it takes to close a buy, I do not look for when he calls for payment.
I do not even look for the mold after payment, I have 11 of his molds.
I look at how good the boolits look when I use the mold.
I sometimes wish I could shake his hand, I do not see that happening soon.

^^^ What he said! ^^^

[paul h]

Not to knock other mold makers, but I can't think of any mold maker that produces a hollow point mold of the same quality as MP, and considering the quality and intricacy of the machine work, they are an exceptionally good deal.

Well worth the wait.

[frankensteiner]

I would like one 4 cavity GC with standard HP pin, Blank pin, and long pins.

frankencraigslist at gmail dot com

[chuck4570]

Change mine to all pins please.

[RED333]

New Years bump

[Gelandangan]

Ok just purchased a similar NOE mold from a mate.

Please remove my name from the list #12

Sorry for inconveniences.

[jeremiah.allen1]

One four cavity with all pins
jeremiah(dot)allen1553(at)gmail(dot)com

[Diegokid]

Put me down for a 4 cavity with all pins. With gas check.
diegokid at bellsouth dot net

[45 2.1]

One four cavity with all pins

Jeremiah. I need to know whether you want a plain base or gas check base.

One more day toward it getting made.

Thread Updated...................

[jbremount]

Please remove me from the list. I am #49.

[crawfobj]

4 cavity plain base, with all the pins please.

Bryan_crawford98 at yahoo dot com

[Diegokid]

Before getting excited what are the thoughts for using this mold for a 7.62x39 with a 1 in 10 twist for subsonic use?

[45 2.1]

Before getting excited what are the thoughts for using this mold for a 7.62x39 with a 1 in 10 twist for subsonic use?

There has been a lot written in the past about using this weight in the 30/357 case or similar cases like the 30 Badger which is a bottle neck on the 38 Special cases. It proved stable in these small cases at small game distances at velocities lower than what you seek.

[ipijohn]

Before getting excited what are the thoughts for using this mold for a 7.62x39 with a 1 in 10 twist for subsonic use?

I am planning on using mine in my 300 AAC Blackout (7.62X35mm) it's 4 mm shorter than the AK round but I'm thinking that I can make it work. If not I will try it in my .308, 54R or 30-06.

[Viagrow]

Please sign me up,

Viagrow.....brian_tnd at hotmail dot com.....One 4 cavity gas check with all pins.

Regards...

[sureweld78]

Alva34 at hotmail dot com.... One 4 cavity plain base with the long 311410 pins. One set of handles.

[silverjay]

One two cavity gas check with flat and short pins.

Silverjay7 at gmail dot com

thanks

[xacex]

What did Bob do to get banned? I hope it is just a time out. Many of the Mihec group buys are hancho'd by him this one included.