Please add me on for a 2 Cavity 226 gr HPPB RTL w/standard pins and an extra set of blank pins. Estimated cost $113.
Schutzen sldietsch at wk dot net
Please add me on for a 2 Cavity 226 gr HPPB RTL w/standard pins and an extra set of blank pins. Estimated cost $113.
Schutzen sldietsch at wk dot net
Put me down for a 2 cavity 300blk mold gc and hp with standard and penta pins if available.
ΜOΛΩΝ ΛΑΒΕ
I will take a four cavity PB with standard hp pens shown , and short hp pens. Thanks
Last edited by woody13; 04-18-2014 at 02:13 AM.
I am interested what the weight would be with the long or short 311410 pins would be. Any chance it is right around 200 grains? It may shoot well and stabilize in a 30-06 then, but the H/P would cause it to peal back pretty bad, and break apart at higher velocity. Getting it to retain weight through an animal could be a challenge at 2300fps, but should be very effective regardless.
Will take a 4 cavity plain base with all the pins, toboter at aol dot com, thanks for getting this together
Al
Is it possible to get a 4 cavity with 2 PB and 2 GC? Or would I need to get separate molds?
mine is
m l woodall 13 "at" hot mail . com
If it's not to late, I would like to add a set of long pins to my order.
I'll take one. Plain base. Standard hollow point pins 4 cav.
Can I order more pins at a later date?
I would like to buy a 4 cavity PB set. As for pins I will take both the std set of HP pins it comes with, the deep set of pins, and a set of shallow pins. Ideally I am looking for a weight around 230 to 210 that I can manipulate with the pins. The extra long pins appeal to me if it won't bend the bullet when dropped though I can drop into water to harden it if needed.
Also, TY 45 2.1 for doing a hell of a lot of heavy lifting working on the design and redesigns to make it feed etc. it is appreciated.
If you have any suggestions I am open to it. I only have experience casting miha pistol bullets so this will be my first miha rifle bullet set,figure its the same but eh never know till one tries..
Dr. Moo
sdolinkodvm at gmail dot com
Last edited by Dr. Moo; 05-17-2014 at 09:28 PM.
pyrofx
4 cav gas check .
short hp pin
pyrofx@citlink.net.dropthis
I'll take a four cavity gas check mold with standard hp pin set. My email is jasonbrimley11 at gmail dot com.
ill take one
2 cavity, PB, long and short pins
nwalker73athotmaildotcom
Change mine to include all pins please.
I'll take one.
4 cavity
plain base
All pins for this buy
wordturd
wordturd71 AT gmail DOT com
I will take a 4 cav, PB with all pins.
b (underscore) maney at verizon dot net
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |