RepackboxLee PrecisionSnyders JerkyInline Fabrication
Reloading EverythingMidSouth Shooters SupplyRotoMetals2Titan Reloading
Load Data Wideners
Page 1 of 7 1234567 LastLast
Results 1 to 20 of 124

Thread: MiHec 433640 Light brass two or four cavity Cramer HP or solid, GC or PB

  1. #1
    Banned 45 2.1's Avatar
    Join Date
    Mar 2005
    Location
    Little Egypt, Part of the political fifedom of Chicago
    Posts
    7,099

    MiHec 433640 Light brass two or four cavity Cramer HP or solid, GC or PB

    MiHec 433640 Light brass two or four cavity Cramer HP or solid, GC or PB

    This is a new design boolit and is available in 0.433" as a gas check or plain based boolit. This boolit is suitable for the 44 Special and Magnum. It has a shorter 0.310"nose, meplat to crimp groove, to work in the lever action rifles in these calibers. It will weigh about 224 gr. as cast dependent on your alloy of choice and has a little over a 70% meplat.

    For the two cavity solid, the price is $75 with plus $15 shipping.

    For the two cavity Cramer HP, the price is $90 with one set of pins included plus $8 per extra pin set if wanted plus $15 shipping.

    For the four cavity solid, the price is $90 with plus $15 shipping.

    For the four cavity Cramer HP, the price is $120 with one set of pins included plus $16 per extra pin set if wanted plus $20 shipping.

    Cramer Pin options: 1) large HP, 2) small HP, 3) penta HP, 4) cup HP, 5) blank pins for solid.

    If the HP pins are not suitable for reversal to a solid, the blank pins come with the price of the mold. If you do not want the HP pin sticking out of the base of the mold, in the case of reversible pins, you can order a set of blank pins for a smooth mold bottom.

    Sequence of events: Participants order molds and are placed on the list, the Group Buy will close (which will be posted on the thread) at some time determined by MiHec, the molds are made from the orders on the list at the time it is closed or by altering what you want via PM to MiHec after it's closed. Extra molds should be available... order them by PM to MiHec. Invoices will be sent out via e-mail from the listed addresses and you pay by using Paypal...... It is my understanding the invoice will be in Euros which Paypal converts from Euros to dollars. After you pay, the mold gets shipped.

    Prices are somewhat variable due to the exchange rate.... be aware of this.

    Please give your disguised e-mail address, either a 2 or 4 cavity mold, gas check or plain base, the number of molds and type with pin options you want if applicable.

    Sign Up List:
    1. dancingbear41.....dancingbear41 at btinternet dot com.....One 4 cavity plain base Cramer with large and penta pins
    2. Cowboy Dan.....mauckdan [at] gmail [dot] com .....One 2 cavity plain base Cramer with small, penta and cup pins
    3. SethD.....seth doty 4 44 at hot mai l dot com.....One 4 cavity plain base Cramer with large pins
    4. GLL.....gllewis at pasadena dot edu.....One 4 cavity plain base Solid AND One 4 cavity gas check Cramer with large pins
    5. AZBrian.....sellsell(at)cox(d0t)net.....One 4 cavity gas check Cramer with all pins
    6. sister jim.....sister jim at hot male dot com .....One 4 cavity plain base Solid
    7. BruMatt.....Jmwbruce at aol dot com.....One 4 cavity plain base Cramer with large and cup HP pins and One set of handles
    8. Olevern.....midimize at wildblue dot net.....One 4 cavity plain base Solid
    9. gtgeorge.....gspatton at gttransmissions dot com.....One 4 cavity plain base Cramer with all pins
    10. uaskme.....pardue10 at Comcast dot net.....One 4 cavity plain base Cramer with all pins
    11. WARD O.....ward dot olson AT yahoo DOT com.....One 2 cavity gas check Cramer with large, penta and cup HP pins
    12. autodidact.....jbpaul (at) suddenlink (dot) net.....One 4 cavity gas check Cramer with all pins
    13. Luskejeger.....kri_stiansen AT yahoo DOT no.....One 4 cavity gas check Cramer with all pins
    14. BK7saum.....Bradleyk4860 AT gmail DOT com.....One 4 cavity plain base Cramer with all pins
    15. Nix.....greg at tacticaladvantage dot ca.....One 4 cavity plain base Cramer with large and penta pins
    16. AnthonyB.....anthonyb45 at verizon dot net.....One 4 cavity gas check Cramer with all pins
    17. ValorsMinion.....strafeology (@t) gmail (Dot) com.....One 2 cavity gas check Cramer with all pins
    18. tja6435.....Tja6435 at gmaildotco.....One 4 cavity plain base Cramer with large pins
    19. 44bear.....art dot dyck at hotmail dot com.....One 4 cavity plain base Cramer with large and small pins And One 4 cavity gas check Cramer with cup and penta pins
    20. alha.....snowserver (a*t) hotmail DOT com.....One 4 cavity plain base Cramer with all pins AND One 4 cavity gas check Cramer with all pins
    21. Loc n Load.....Wewestjr01 at frontier dot com.....One 4 cavity gas check Cramer with large, small, penta and blank pins
    22. taugust.....g99jeb at aol dot com.....One 4 cavity plain base Solid
    23. bcr.....brichards at optics dawt arizona dawt edu.....One 4 cavity plain base Cramer with large, small and blank pins
    24. doctorggg.....gggmmg at verizon dot net.....One 4 cavity plain base Solid
    25. Balduran .....jkoskelaATfinning.ca.....One 4 cavity gas check Solid
    26. 9w1911.....ninthwardskis at gmail.com.....One 2 cavity gas check Cramer with ??? pins
    27. Loc n Load.....Wewestjr01 at frontier dot com.....One 4 cavity plain base Cramer with large, small, penta and blank pins
    28. bigarm.....paula one eight zero at centurytel.net.....One 2 cavity plain base Cramer with large and blank pins
    29. tward.....tward91574 at aol dot com.....One 2 cavity plain base Cramer with all pins
    30.
    Attached Thumbnails Attached Thumbnails MiHec 433640 Light.jpg  
    Last edited by 45 2.1; 01-21-2015 at 05:53 PM.

  2. #2
    Boolit Buddy
    Join Date
    Jun 2011
    Location
    Utah
    Posts
    350
    Sign me up. 4 cavity all pins plain base. email is
    my guy b at g mail dot com

    Bardo

  3. #3
    Boolit Buddy PWS's Avatar
    Join Date
    Dec 2010
    Location
    Kodiak, AK
    Posts
    266
    Plain base, 4 cavity, large hollow point pins, mikefairbanks45 at yahoo dot com

  4. #4
    Boolit Man
    Join Date
    Nov 2009
    Location
    TX
    Posts
    96
    4 cavity, PB, large hollow point pins only. (seth doty 4 44 at hot mai l dot com)

  5. #5
    Boolit Master
    GLL's Avatar
    Join Date
    Mar 2005
    Location
    California
    Posts
    3,580
    I will take a 4-cavity solid plain base.

    Jerry

    gllewis at pasadena dot edu
    S&W .38/44 Outdoorsman Accumulator

  6. #6
    Boolit Buddy AZBrian's Avatar
    Join Date
    Sep 2013
    Location
    Chandler, AZ
    Posts
    108
    I'd like a 4 cavity HP with all pin options, please.

    sellsell(at)cox(d0t)net

    Thank you!

    EDIT: Gas Check option, please
    Last edited by AZBrian; 10-03-2014 at 01:17 PM.

  7. #7
    Boolit Buddy
    Join Date
    Jun 2011
    Location
    Utah
    Posts
    350
    There isnt as much intrest for this as I thought there would be. Bump to the top.

    Bardo

  8. #8
    Boolit Buddy PWS's Avatar
    Join Date
    Dec 2010
    Location
    Kodiak, AK
    Posts
    266
    Quote Originally Posted by Bardo View Post
    There isnt as much intrest for this as I thought there would be. Bump to the top.

    Bardo
    Ya, I figured this bullet would be the berries for any and all .44Spl snubbies, plus plinkin' and dinkin' in the bigger 44s.

    Maybe guys are holding off because Mihec has a lot to do ahead of this one?

  9. #9
    Boolit Man
    Join Date
    Nov 2009
    Location
    TX
    Posts
    96
    One thing to keep in mind is that there have been several bullets run that fill much the same role recently. It will pick up in time.

  10. #10
    Boolit Buddy kevmc's Avatar
    Join Date
    Mar 2013
    Location
    W. Central IN
    Posts
    275
    Quote Originally Posted by PWS View Post
    Maybe guys are holding off because Mihec has a lot to do ahead of this one?
    That would be me...watching....love to have one soon.....guessing this one will take a year or so...???

  11. #11
    HONCHO EMERITUS


    Dutch4122's Avatar
    Join Date
    Mar 2005
    Location
    ??????
    Posts
    1,754
    I'll take:

    one 4 cavity plain base mold with a set of cup h/p pins and a set of blank pins

    and

    one 4 cavity gas check mold with a set of cup h/p pins and a set of blank pins

    dutch4122(at)yahoo(dot)com
    -Matt
    Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN

  12. #12
    Banned 45 2.1's Avatar
    Join Date
    Mar 2005
    Location
    Little Egypt, Part of the political fifedom of Chicago
    Posts
    7,099
    Quote Originally Posted by AZBrian View Post
    I'd like a 4 cavity HP with all pin options, please.
    Gas check or plain base mold ????????

    Thread updated............

  13. #13
    Boolit Bub
    Join Date
    Nov 2012
    Posts
    67
    I'll take a 4 C PB large and cup pins w/handles
    Jmwbruce at aol dot com

  14. #14
    Boolit Buddy
    Join Date
    May 2009
    Location
    Idaho
    Posts
    281
    Any chance this mold will be made in either 0.431 or 0.432? In the past, many of the 44cal MiHec molds were made with a choice of 0.432 or 0.434. I understand that the larger sizes are needed for some Marlins. I size to 0.430in for my Smith 629DX using WW alloy with 2% tin. Sizing down 3 or 4 thousands in my Star is sometimes a bit much depending on bullet design.
    Thanks,
    Bill
    Idaho

  15. #15
    Boolit Master
    Join Date
    Aug 2006
    Posts
    1,384
    I'll take a four cavity solid, please.

    midimize at wildblue dot net

    edit: plain base
    Last edited by Olevern; 03-28-2014 at 09:25 AM.
    "The trick is to stop thinking of it as 'your' money" (Tax Auditor)

    Life is not waiting for the storm to subside, life is about learning to dance in the rain.

  16. #16
    Boolit Master gtgeorge's Avatar
    Join Date
    May 2011
    Location
    Deer woods of GA
    Posts
    617
    Please add me for a 4-cavity PB with all pins. gspatton at gttransmissions dot com

  17. #17
    Boolit Buddy
    Join Date
    Sep 2011
    Posts
    127
    I will take a 4C PB with all pins. pardue10 at Comcast dot net

  18. #18
    Banned 45 2.1's Avatar
    Join Date
    Mar 2005
    Location
    Little Egypt, Part of the political fifedom of Chicago
    Posts
    7,099
    Quote Originally Posted by wdr2 View Post
    Any chance this mold will be made in either 0.431 or 0.432?
    You would have to ask MiHec that. The problem with cutting a smaller diameter is the gas check shank would be that much smaller (if what you're wanting is the GC version). Not so much a problem with a plain base mold other than a different set-up (and time involved) for it.

    Thread updated............

  19. #19
    Boolit Master
    Join Date
    Jun 2008
    Location
    TWIN CITIES
    Posts
    727
    I would like a two cavity Cramer style with the large pins, penta pins and cupped pins please.

    wolson AT rfgdistributing DOT com

    Thanks
    ward

    Sorry -- forgot to say GAS CHECK please.
    Last edited by WARD O; 04-17-2014 at 03:35 PM.
    "To anger a conservative, lie to him. To anger a liberal, tell him the truth." —Theodore Roosevelt"

  20. #20
    Banned 45 2.1's Avatar
    Join Date
    Mar 2005
    Location
    Little Egypt, Part of the political fifedom of Chicago
    Posts
    7,099
    Quote Originally Posted by WARD O View Post
    I would like a two cavity Cramer style with the large pins, penta pins and cupped pins please. Thanks ward
    Gas checked or plain base?????????

    Thread updated............

Page 1 of 7 1234567 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check