A.C.E. Co 5.56 Heavy

[338RemUltraMag]

Good question, I am going to put a tentative $200 on it but it could be more.

[Wayne S]

The listed prices are + S& H which is $ _____
dimensions of each block size ? and which size blocks for 4, 6, & 8 cavity molds.
Put me down for a 6 cavity, depending on block size , and did you finalize on sprue plate thickness and the Dia. of the holes in said olate ??

[338RemUltraMag]

Wayne,

The block/cavity ratio will be proportional to optimize the heat of the mold. I know I can get 8 in the large block, possibly 10 the medium block will be 6-8 and the small 3-4.

if there is room for 10 cavities I will then see if I can double side it to make a 20 cavity.

The hole size is going to be .110 the thickness will be 1/8" stainless steel.

[358wcf]

338RUM-
I really like the looks of this one-
I'd be in for a 4cavity mold-

NOW the BIG QUESTION!
Any chance you could open this up just a bit, to perhaps .228 or .229 for use in my 22HiPower????
I know I could "beagle" the mold a bit, or send it to Erik at Hollowpoint Mold Svc to have the driving bands enlarged, but would rather have a proper mold cut to the proper dimensions--
Just dreaming, but it can't hurt to ask--

358wcf Chuck

[338RemUltraMag]

358WCF,

I could pop it out, would you want one or two molds one each of .227 then .229-.230?

Or just one at the bigger diameter?

[338RemUltraMag]

10 cavity is a go

[Wayne S]

I would like to know the external measurements of the different size blocks, and a send the $$$ to address.

[bnelson06]

It am going to unfortunately have to drop out of this great buy, my wife thinks buying lp to keep us warm is more important

[338RemUltraMag]

It am going to unfortunately have to drop out of this great buy, my wife thinks buying lp to keep us warm is more important

Family first, I am not going anywhere.

It is going to be at least 3-4 weeks before the call for payment do you want to hang on or no?

[bnelson06]

I might be able to swing it by then so yea I'll hang on by a thread

[Bjornb]

I'll take a 4-cav.

[338RemUltraMag]

Updated

[357shooter]

I'll take an 8 cavity. Nice design!

[Wayne S]

Cherry is on order.

Cherry ordered 22 Jan. A SWAG of 4 weeks from order to delivery =28 days, or (9 + 10) = 19 - 28 = 19 Feb. Start cutting molds (+ -) 24 Feb.

[338RemUltraMag]

Yes sir you are pretty close, once we get the cherry it will be a week till they are ran.

[mikedp]

Handles will be Lee 6 cavs and I will have to check the top punch, I may have to make up some "blank" punches like the professor makes.

Quick question about Lee handles...are the 6 cavity handles different from the 2 cavity?

[Wayne S]

Quick question about Lee handles...are the 6 cavity handles different from the 2 cavity?

VERY different, for your knowledge, Lee 2 cavity molds come with permanently attached handles. Lee 6 cavity mold handles are sold separate and can be used on a verity of molds

[Viagrow]

http://castboolits.gunloads.com/show...431-Noe-225-70
Both SJ & I were using 1-9 barrels. I traded for the bullets I shot, from my rifle, shooting my bullets I'll expect 10 shot groups of 1.5" or less.

Thank you for the reply sir.

[Viagrow]

Please add me to the interested party list. My interest is in a 6 cavity mold, but I will entertain whatever number cavity the group goes with. Thanks...

[wiersy111]

I'm interested in a 6 cavity. Any posibility of a hollow point? I think this would be great hollow pointed.