ADvertise hereStainLess Steel MediaLee PrecisionGraf & Sons
RotoMetals2Inline FabricationTitan Reloading

Page 37 of 37 FirstFirst ... 2728293031323334353637
Results 721 to 736 of 736

Thread: C'mon In Lurkers.

  1. #721
    Boolit Master dbosman's Avatar
    Join Date
    Feb 2013
    Location
    East Lansing, MI, USA
    Posts
    1,574
    For those who have rendering equipment, (I'm on a personal crusade to erase the word smelting as it isn't what we do. We recycle) ladle casting from your rendering pot uses energy but works. Don't let a lack of an electric pot hold you back.

    For those lusting after a ladle, if you're at all handy you can make a very serviceable ladle from a stainless steel spoon. I like round bottom measuring spoons. A vise makes this simpler, but you can use a nail and hammer to tap (bash) a pour spout into one or both sides. Then a length of slit 3/4 dowel for an insulating handle. Drill and bolt, JB Weld, or just wrap the handle tight with wire to secure the handle. Mine cost 29 cents at a thrift store.

  2. #722
    Boolit Master

    Join Date
    Jan 2013
    Location
    West Virginia
    Posts
    986
    Quote Originally Posted by PtMD989 View Post
    New guy from Mi thumb. Been lurking for awhile finally joined. I'm working on gathering my stuff to cast boolits for my T/C Black Diamond.50 cal.
    Welcome aboard !!! I spent most of my life in the thumb area except for 8 years over in the Muskegon and Grand Haven area, 5 years in NYC and now retired in West Virginia.
    Lead bullets Matter

    There are three kinds of men: The ones that learn by reading. The few who learn by observation. The rest of them have to pee on the electric fence and find out for themselves. - Will Rodgers

  3. #723
    It's a small world. I live in southern Tuscola co. We've vacationed over in Grand Haven a few times. It's beautiful on that side of Mi.


    Sent from my iPhone using Tapatalk

  4. #724
    Boolit Master

    Join Date
    Jan 2013
    Location
    West Virginia
    Posts
    986
    Quote Originally Posted by PtMD989 View Post
    It's a small world. I live in southern Tuscola co. We've vacationed over in Grand Haven a few times. It's beautiful on that side of Mi.


    Sent from my iPhone using Tapatalk
    August 4 was always a good time in Grand Haven celebrating the Coast Guards Birthday. Closed off Washington St. for 3 blocks and put a carnival there for a week.
    Lead bullets Matter

    There are three kinds of men: The ones that learn by reading. The few who learn by observation. The rest of them have to pee on the electric fence and find out for themselves. - Will Rodgers

  5. #725
    Quote Originally Posted by 62chevy View Post
    August 4 was always a good time in Grand Haven celebrating the Coast Guards Birthday. Closed off Washington St. for 3 blocks and put a carnival there for a week.
    We missed that by 2 weeks. The lighted musical fountain is cool. Checking out Fishermans Pier and the Boardwalk is fun. The charters hit the kings good that week. In Muskegon we hit the amusement park and toured the USS Silversides. It takes a little bit to get used to those Mi lefts.


    Sent from my iPhone using Tapatalk

  6. #726
    Boolit Master

    Join Date
    Jan 2013
    Location
    West Virginia
    Posts
    986
    Quote Originally Posted by PtMD989 View Post
    We missed that by 2 weeks. The lighted musical fountain is cool. Checking out Fishermans Pier and the Boardwalk is fun. The charters hit the kings good that week. In Muskegon we hit the amusement park and toured the USS Silversides. It takes a little bit to get used to those Mi lefts.


    Sent from my iPhone using Tapatalk
    LOL they are a bit different left turn. I haven't been back for more than a day or two since 1992, mostly to Muskegon with the Out Laws Burton for my side.
    Lead bullets Matter

    There are three kinds of men: The ones that learn by reading. The few who learn by observation. The rest of them have to pee on the electric fence and find out for themselves. - Will Rodgers

  7. #727
    Boolit Mold MuthaFunk's Avatar
    Join Date
    Apr 2016
    Location
    Ontario Canada
    Posts
    10
    Hi everyone!! I have been enthusiastically casting boolits for about a year and a half now. I want to thank all the contributors for posting so much of their many many years of experience on this forum. I've been learning so much from this site but unable to post for the longest time due to a problem with my email confirmation and the castboolits forum. After a year of off and on attempts to get my account unlocked to be able to post, I'm finally here!!!

    I'm looking forward to direct interactions with everyone here!

  8. #728
    Boolit Bub
    Join Date
    Jan 2017
    Location
    Franklin, VA
    Posts
    31
    First post - glad to be here. Been reading this forum for years but just started casting.

  9. #729
    Boolit Mold
    Join Date
    Mar 2017
    Location
    Behind enemy lines. (California)
    Posts
    2
    Hi all,
    I've been lurking on the forums for a while now. I've been casting round ball for my .50 Hawken for a couple of years now. I also used to reload quite a few jacketed bullets for .308 win, but that was 20 years ago.

    Last week, I picked up a never fired Marlin 336CS (Made in 1992). Now I want to start shooting boolits. I'm finding all kinds of great info here, as I try to figure out all the different molds, sizers, gas checks, etc.

    Thanks,
    Greg

  10. #730
    Boolit Man Ateam's Avatar
    Join Date
    Mar 2017
    Location
    Northern MI
    Posts
    105
    Well I guess since you asked so nice, no more lurking. Found this site while struggling with a lyman 330grn Gould mold, darn hollow points. The amount I have learned lurking here has been amazing. I think I might be hooked.

  11. #731
    Boolit Buddy retrobass's Avatar
    Join Date
    May 2017
    Location
    Georgia
    Posts
    72
    Longtime lurker, finally decided to join up. Right now I've got an RCBS bottom pour with PID, three 9mm molds (just got a brand new Lee 6 cav 120 TC I've yet to try), and some basic PC supplies I've successfully used. My main goal is to reduce cost so I can put a higher volume of handgun rounds down range, and up my skill level. Looking forward to learning a lot more from you guys!

  12. #732
    Boolit Bub
    Join Date
    Apr 2017
    Location
    Missouri
    Posts
    22
    Hello,
    I've been reloading for a number of years in several calibers, but using j-word bullets and mostly for rifles. A few years ago I started buying MBC cast boolits for pistols and had been satisfied, but I'm always yearning for more. This forum has come up many times when searching for answers to questions posed via the internet. In the last few months I have been wanting to cast my own boolits and have been reading posts here voraciously. I've also read "Ingots to Targets" looking for information.

    I have not yet cast a single boolit, but I have been gathering supplies. My plan is to use a gas powered plumber's furnace with cast iron pot/pans to make ingots from range scrap (j-word bullets with some shotgun buck and slugs) and then ladle pour boolits to powder coat. I have a spare tumbler and will likely use that for applying the PC and will obtain a convection toaster oven for baking. Initially, I will be casting for .45 ACP and if all goes well then .38 Special and 9mm. Assuming that goes well, .458, .308, and .311 caliber rifle will be next. I really want to find an acceptable load for subsonic .308 Win using CB's and my .458 SOCOM is expensive to shoot with j-word bullets.

    I'm sure I will want to get an electric bottom pour pot to speed production after getting started. I need to get molds yet, but most everything else I have or will shortly. I'm excited to start down this rabbit hole and appreciate all the hard work done before me to make it easier for me to begin! I have a whole lot to learn and am willing to do so. I hope to contribute as well when I have knowledge or experience to do so. Another hobby is gas powered appliances such as Coleman lanterns and stoves, so if you have a question about those, fire away!

    Thanks allowing me to join!

  13. #733
    Cast Boolits Owner

    No_1's Avatar
    Join Date
    Mar 2005
    Location
    N.E. Florida
    Posts
    6,403
    Welcome aboard!
    "Things always get better once thought, time, and money are applied in the correct amounts at the correct time"
    - No_1 -

    "The only way to deal with an unfree world is to become so absolutely free
    that your very existence is an act of rebellion."
    - Albert Camus -

  14. #734
    Thanks to all of the contributors that taught me solutions to multiple problems with casting. Last week every bullet was wrinkled. This week, every bullet of 943 cast, except one, was near perfect.

  15. #735
    Boolit Mold trumpychris's Avatar
    Join Date
    Jul 2012
    Location
    Queensland Australia
    Posts
    1
    Hi to all here. I've been a registered member on this forum since 2012 but today I thought I'd actually say g'day.

    I've been a shooter since the age of 5, have been reloading for 10 years, casting for about 7. I have picked up some very handy tips from this forum that have kept me away from a lot of the pitfalls that are experienced by the beginner.

    I still consider myself to be a novice when it comes to casting but my skills are improving with every session.

    I currently own 13 molds, the majority being Lee and Cast Bullet Engineering. I am lucky enough to shoot at the same small country range as David Commens, the owner of CBE. I just drop him an email and a few days later I pop into his workshop and pick them up.

    About 2 years ago I moved from a ladle & saucepan over gas to a Lee 25lb bottom pour and I wish I had done it a lot sooner. I still do very small batches of soft lead for BP shooting with the ladle, Its easier than dumping the lead from my pot for the sake of casting 20 bullets.

    If i'm not at work, usually I am in the reloading room or shooting on my own private range that I built on my small farm.

    Cheers

    Chris

  16. #736
    Boolit Mold dansmach's Avatar
    Join Date
    Jul 2017
    Location
    St. Cloud, Florida
    Posts
    6
    Okay, I'm in the water. Up to my ankles but in none the less. I've been considering casting my own bullets for a little while now but haven't pulled the trigger just yet. If I get into it, I'd like to go with coated bullets (which I've looked into). Still looking into the initial equipment needed and really like the idea of a bullet feeder when it comes time to size them. Slowly learning my way around the forum and hope to pick your brains for ideas. Thanks


    Sent from my iPhone using Tapatalk

Page 37 of 37 FirstFirst ... 2728293031323334353637

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check