Ok, finally got my tapatalk issues straightened out so I can edit my posts again. Got the list updated. Please check that your order info has been recorded correctly. I do make mistakes.
Ok, finally got my tapatalk issues straightened out so I can edit my posts again. Got the list updated. Please check that your order info has been recorded correctly. I do make mistakes.
Add me for a 434 GC with pins and a 432 plain base with pins. Waggoner at msstate dot edu
Charlie Waggoner
Add me for a 434GC with all the pins. joshquerin at hotmale dot com
Any idea what handles a 2C uses? Also if there is anyway this can be offered in a 4C move my order to it please. I'm sure there has got to be some people who would rather have a 4C.
I would also prefer a 4 cavity if one is offered.
Please put me down for a 2-cav 2-GC in .432".
What alloy are these being designed for to drop at 'as-cast' diameters? (... just in case I need to add a .0001" to the diameter by manipulating alloy.)
One mold, .432 plain base with both pin sets.
charles unndeerscoor nuss aat yyahho dooot coooom
1. Please edit your post to include your paypal email address.
2. Wheel weight alloy. However, Miha usually cuts the cavities on the very outter edge (large) of the spec. I think you'll be ok with whatever alloy you use, or else you really should have ordered the .434"
I'm in for a .432 GC version - msp 2640 at hotmail dot com (no spaces and change the dot) - Thanks Bill in MA
Has it been determined the different weights the mold will produce?
1 mold .432 non GC smsten ONE at UNITELC dot COM
Kevin
Different weights how? They will all drop within a few grains of 305gr.
I was wondering if the bullet weight was determined with each of the pins. I just wanted a ballpark estimate.
Will depend on alloy but.... The drawing of the large hp cavity says "-10gr Hollow Point". So I would guess that would take the 305gr solid down to 295gr. So compared to the big hp maybe -4gr for the penta hp.
Oh, I see. Yes, the conical hp is -10gr exactly. The penta will be more like -6gr or so.
I would like the .434 pb with all pins. hicardattheskybeamdotcom
Mihec, I have a new email address. It is: hicard21 at outlook dot com
Last edited by hicard; 01-11-2014 at 10:47 AM.
This country has gone to hell but now there is hope for us.
I'm curious to know what the diameter of the area just in front of the first crimp groove (8.001 mm from meplat) is on the .432" design.
I plan to use this bullet specifically in the 444 Marlin, and this dimension is important for chambering (ala Glen Fryxell).
NOTE: Any of you who have examples from a previous GB mold could answer this question (hopefully). Thanks!
Last edited by NYBushBro; 11-25-2013 at 11:11 AM. Reason: addendum
You should ask your question in the results thread too.
I'll take a .434 gc with all pins thanks
Icecold at izoom dot net
I will take 1 .432 GC with all the pins. If you have in a 4 cav will take instead. thanks
foster dot jess at gmail dot com
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |