Cast .410 Slug

[longusmc]

Would bullets cast from a Lyman 410610 work as a suitable slug for a 2 1/2" .410. this mold casts at +/-215 grs which is close to 1/2 an ounce.

My Lyman manual does not have any data for .410 slug loads, so I'll be hunting down an additional manual for .410 data. What recommendations do you have?

Thanks

[Randy C]

Ballistic products has some of the best manuals for shotguns.

[longusmc]

I have their Advantages Manual but it doesn't have any slug loads listed.

[Randy C]

http://www.ballisticproducts.com/Slu...tinfo/00MSLUG/
This is there loading manual for slugs. I would think some one here would have it and let you know if it had the loads you need or take the time to post some, I don't usually post unless I scan the page, there's know typing errors that way.
Randy

I went and looked I have there 3rd edition

They have a listing of 4 loads for 2 1/2" and 3" they are for 84gr LGS-41 Slug but they are to light, here is the Buckshot loads.

There is 2 / 208gr buckshot 2 1/2" loads
Load Id, Powder, Grains, Primer, Wad Column,
41012-482 Longshot 8gr Ched-209 Stretch+(4)00 pellets
PSI 11500 FPS 1200 OS41 over shot card

41012-580 H110 16gr Ched-209 Stretch+(4)00 pellets
PSI 7400 FPS 1200 OS41 over shot card

There is 2 / 201gr buckshot 3" loads

80271-484 Lil' Gun 18gr Ched-209 BX410 + (3)000
(2) NC41 over shot
PSI 11100 FPS 1460

80271-485 Lil' Gun 20gr Ched-209 BX410 + (3)000
(2) NC41 over shot
PSI 11700 FPS 1570

If you use any of this data I would email them to make sure it will work I don't know if your slug will fit in a these wads.

[Randy C]

I had this info typed in columns but when I posted it pushed it all together.

[SuperBlazingSabots]

Hello Longusmc, perhaps this will help:

http://slugshooting.accountsupport.c...hp?f=32&t=1513

I'm proud to be a Elite Musketeer, among other Elite Musketeer's here.

Best regards,
Ajay
SuperBlazingSabots,com
BlazingSabots@Gmail.com
http://www.facebook.com/BlazingSabots?ref=hl[/url]
http://slugshooting.accountsupport.com/[/url] ... wforum.php
http://castboolits.gunloads.com/showthr[/url] ... ot!/page1
http://www.shotgunworld.com/bbs/view...f=118&t=196961[/url]
http://www.deeranddeerhunting.com/fo...p?f=43&t=39246[/url]
http://www.go2gbo.com/forums/slug-gu...old-is-gold-!/[/url]
-Elite Group of Slug Shooter's
We all, who take slug loading seriously are a dedicated family, who have taken it upon ourselves to perfect our tech. We experiment to find better techniques and share our knowledge.
Location: New Jersey. USA / Frankfort, W.Germany / London, UK
-Elite Group of Slug Shooter's
We all, who take slug loading seriously are a dedicated family, who have taken it upon ourselves to perfect our tech. We experiment to find better techniques and share our knowledge.

[jmort]

I just got the Ballistics Products Slug Manual and will check it out when I get home tonight and see if it is any newer than the third edition or has any more/different data. Also got the newest Buckshot manual which just came out a few weeks ago. Both cover .410 I believe and have some data, not a whole lot, but some. Give me a few hours and I'll get you some info.

[cpileri]

I was going to offer the same info from the same manuals, but others have you covered. Other daya will be any shot loads over 1/2oz in the 2.5" 410 should be safe.
One load that has made rounds on the net is 8gr-to-16gr of Alliant 2400 w a 210gr slug, wadcutter loaded nose down (backwards) into a BPI stumpy wad (*); no velocity info though. But I have tried the 8gr load in a full choke 410 and it shot straight without bulging the choke.
C-
(*) this wad: http://www.ballisticproducts.com/Stump-410-cupless-wad-250_bag/productinfo/0724105/

[longusmc]

Thanks for the info. I'm considering loading these in a blownout .303 case for a .410 Enfield. I'm sure there will be enough room in the case as from what I have read most wads are a little loose.

[Randy C]

Thanks for the info. I'm considering loading these in a blownout .303 case for a .410 Enfield. I'm sure there will be enough room in the case as from what I have read most wads are a little loose.

I have the buckshot lll / Manual / It has 3" 410 in 1/2oz 5/8oz and 3/4oz if you want them let me know.

[longusmc]

Thanks for the offer, however this will probably be limited to data for 2 1/2" shells.

[Randy C]

For who is interested.

[Randy C]

SuperBlazingSabots Ajay that's a good article I will have to save it for my reload book.

[cpileri]

Here is some 2.5" 410 load w 1/2 oz buckshot style from the BPI manuals:


Sorry if its not right side up.
C-

[Randy C]

up side down, lets see the 3" loads also

[SuperBlazingSabots]

A good post for our .410 lovers, enjoy it.

Regards,
Ajay K. Madan
Super Blazing Sabots

[uncle dino]

The only issue I see with that mold is that it is not hollow base and the slug will tumble. For smooth bore the slug must be a weight forward design. Rifled barrel it would be fine. D

[SuperBlazingSabots]

Biker Beans had a great faster load I saw today around 1800 to 1900 fps.
I was looking for it.

Ajay K. Madan
Super Blazing Sabots