MiHec 454640 brass two or four cavity cramer hollow point mold

[2ndAmendmentNut]

Put me down for a 4 cavity please with blank and large HP pins.

willthekid45(at)yahoo(dot)com

[45 2.1]

How is this in a Colt Combat Commander?

Lloyd Smale shot one of the earlier buys in his and said it did fine.

Can this be done for gas checks also? Thanks!

The existing cherry is a plain base version.

Thread updated.............

[USAFrox]

I'll take a 4 cavity Cramer with small and large hp pins. Jasonbrimley11 at gmail dot com.

Question: what size are the penta pins? Are they the same size as the small hp, or the large hp, or somewhere in between?

[45 2.1]

Question: what size are the penta pins? Are they the same size as the small hp, or the large hp, or somewhere in between?

I don't spec the size of the penta pins to MiHec, but do spec the large, small and cup pins since they are round. Generally, the penta pins are as big in diameter at the points as the the large pins and about as deep.... at least on my GBs.

[bushog]

Please add me to the list for one 4 cavity with all pin options.

boo-haaa (at) hot mail dot com

Thanks!

[USAFrox]

I don't spec the size of the penta pins to MiHec, but do spec the large, small and cup pins since they are round. Generally, the penta pins are as big in diameter at the points as the the large pins and about as deep.... at least on my GBs.

Thanks for the answer. In that case, I'll change my order to include only the small hp and the penta pins, please. Thanks!

[TXSlade]

I would like a 2 cavity with all pins please.
andrew dot wilson 33 at gmail dot com

[Pivpav]

olegf9 (at) yandex (dot) ru
One 2 cavity mold, small and penta pins

[Olevern]

Will this be avail. in solid only?

[jethunter]

Hi 45 2.1, I noticed that this boolit is about 30-40 gr. lighter than the original Mihec 454640. Molds from the first run of the Mihec 454640 cast boolits about 277 gr as a solid, or 250 gr with the large HP. My initial interest was in that original heavier boolit.

Is there any chance we could start a GB for the original heavier Mihec 454640?

[cba257]

Hey I realize d that I have one of the molds from the first run. So please take me off the list. Sorry.

[45 2.1]

Will this be avail. in solid only?

No, only in cramer form...... you can get a solid via the blank pins though.

Hi 45 2.1, I noticed that this boolit is about 30-40 gr. lighter than the original Mihec 454640. Molds from the first run of the Mihec 454640 cast boolits about 277 gr as a solid, or 250 gr with the large HP. My initial interest was in that original heavier boolit.

Is there any chance we could start a GB for the original heavier Mihec 454640?

My mistake on the drawing, wrong description and it's fixed now. There is no difference between this and the original MiHec GB.

Thread updated.............

[06ackley]

Im in for a 2 cavity with all pins.
jr442 at frontier dot com

[USAFrox]

I'm #13 on the list. Please remove me from this group buy. I had been wanting this for .45 ACP, and just noticed the earlier post that said this wouldn't be good for it. Thanks.

[BK7saum]

I would like a 4 cavity with large, penta and blank pins.

Bradleyk4860 AT gmail DOT com

[tygar]

I would like a 2 cavity with small HP & solid.
Thanks
Tom
tbrolliniATgciDOTnet

[DEVERS454]

I'm in for this one. I like the weight and the HP design better than some others.

Four cavity, big HP pins. Will paypal immediately.

d m e v e r s @A T@ y a h o o d o t c o m

[DHC]

Please put me down for a 4-cavity mould with all pin options.

icpilot [at] yahoo [dot] com

[mckenziedrums]

Here's hoping all these GB's I'm jumping on are spaced out a bit when the bills come!

4 cavity please. Small, Penta, Blank pins

mckenziedrums at gmail dot com

[45 2.1]

Here's hoping all these GB's I'm jumping on are spaced out a bit when the bills come!

Sure hope so since I'm an excellent enabler.........

Thread updated.............