I run a 4MOA C-more on my Marlin 44Mag
I run a 4MOA C-more on my Marlin 44Mag
Hooroo.
Regards, Trevor.
Australia
What diameter bullets do you use in the trubor?
.3565"
Bore is .355"
Hooroo.
Regards, Trevor.
Australia
Thanks, im yet to measure my bore size. Just at the range with some 357s to see if its any different.
I might need to get Victor to fit a barrel for me.
These were about my best groups today at 50 yards. 122 grain Flat Points in Zombie Green in 38 super. 5.3 grains of AP70, sized to .357. 5 grains wouldn't cycle 100%.
The 357's seemed a bit more consistent than the 356's but that could be my fault too. I don't do a whole lot of practice at 50.
Top group is my workman gun, bottom is my trubor. Aimed at the centre for both but my workman gun is sighted in for Major PF. Going to shoot major tomorrow and try to chrono.
To date this is my most accurate semi auto load so I am pretty happy.
i've slugged my glock barrels anyways.....but...but i reflected that slugged or not, you still have no choice than using the resizers in either 356-57-58 .....so then, there's one size that will fit.just a matter of experimenting with different sizes which will eventually lead to the right size for any given guns.
Dan. What is your OAL?
Vic has all his guns setup to run 31.5mm. with 125Conicals and 125SWC.
A bloke in Brisbane got a new DVC open gun. sent straight to Victor to tune. Bloke then ordered 20,000 125SWC from me cause that is what Victor set his gun up to use. Bloke is happy as larry with how his gun runs.
Karla run a Matt ASI gun and also runs our 125Conicals in it. 31.5mmOAL
Hooroo.
Regards, Trevor.
Australia
I cleaned some old 400 grain Lee boolits and gave them a triple Hi-Tek coating. Loaded 50 rounds and fired them @ 1650 fps, no leading at all and very good accuracy. Fist size rocks @ 50 meters. Even "The Dip" didn't find any lead after a couple of dry patches. Powder residue only - I still haven't slugged the barrel, 4595 is my size now.
Attachment 224304.
This is just great,even though I got carried away from my original suppressed 9mm carbine-mission. That was my reason to try Hi-Tek but it can wait. This crazy summer heat wave needs big boolits.
Now I'm back in time with a 45-70 and I like it!
I can't remember but it is shorter than that due to the flat point. I loaded up a few thousand on Wednesday. It is good enough for me.
I'm going to stick with the 357's. They shoot a little better and I also noticed they don't smoke as much, on Tuesday I used the 356's and got heaps of smoke out of my ports and compensator, almost enough to make me buy tigersharks again. Last night I used the 357's and didn't notice any smoke at all. Both loads were with AP100.
Is it normal for undersized bullets to smoke more? Is the larger size compensating for my hobo lead?
Perhaps you are getting gas blow by with the smaller boolits? You may also experience lower pressure and incomplete combustion with some or all showing as excess smoke?
Hmmm... never noticed it with mine. Have run .356 .3565 .357.
.3565 is the best in mine.
I use sizer dies from Lathesmith on this forum. His dies are the best there are.
Hooroo.
Regards, Trevor.
Australia
Rookie size parcel....
Mine come on a carton the size of a small car.
Need a 3 ton forklift to unload it...
Hooroo.
Regards, Trevor.
Australia
Hehe, hopefully my next order will be a similar size. Now to start playing with hitek to get it working for me. It works for everyone else, i hopefylly stand a small chance
Australia post must have lifted their game, knowing where to send it with a blank label
Great job working out what day to ship it so it would arrive this week. Was a nice trip up north, warmer than it was in Brisbane, that's for sure!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |