Tazza, the correct amount of acetone is 100mls, buy many including myself have used 120ml mix for first coat. I think a lot depends on where your doing the coating and the temp your working under. I coat in a small outside shed with a clear sheeting roof so it gets warm in there at times. I found the copper coating was the one I needed extra acetone on first coat, all others were fine as instructions said. Regards Stephen
I only use 20gms :100mls for both coats.
Never had an issue.
If it ain't broke, don't fix it.
Hooroo.
Regards, Trevor.
Australia
Good to know i can do away with the initial watered down coat.
Stephen: I coat in an outside covered area, it's open on the sides, so it doesn't get stupidly hot during our nasty summers like yours would. Yet i sure can work up a sweat when doing a large batch, almost no need to go to the gym that day when doing big batches. Sadly i have a few hundred kgs worth i need to coat then size..... with the wet weather we have been having, i haven't done anything just in case it messed with bonding with the high humidity
I sent Donnie an email about this and gave him all the details about what I have been dealing with. He said he has not tested this specific batch of blue and can look at it in a week or so. He’s great to deal with and even offered me another color to make up for the problem. Hopefully we’ll get to the bottom of this soon.
This is how I did. Well,it takes me five minutes to hit 180 but I'm staying at 180-185 surface temp 2.30 min then.
My probe meter starts beeping @ 170°C inside temp, then my surface is 182°C. I verify with IR every 30 secs after beep,my temps go higher unless I open the door to take measurements. It's like five seconds open every 30 sec. A manual PID.
Like I posted,recovered TruBlu bullets have coating on grooves.
I'm getting blue bullets with the Tru Blue from Donnie. If my phone would upload the photo to my backup I'd post the photo.
NRA Benefactor.
I know what you mean. All I get is upload of file failed.
Boolits !!!!! Does that mean what I think it do? It do!
Maybe it has something to do with the make over on the site.
Boolits !!!!! Does that mean what I think it do? It do!
slide
I have been trying for years and since I joined this site. Any uploads should work seamlessly if pictures are in a Jpeg mode. From what I was told, the "system" should automatically adjust uploads to allow posting. I don't know how that works. The uploading of pictures and videos, is already established on the system, but using it is a mystery?
May be site controllers can suggest a way to use these facilities.
Thank you in advance....
Back to my blue bullet challenge, Donnie is sending me some from his original batch to see if that makes a difference. If not, I’ll take a dang road trip to Louisiana and get schooled by Donnie himself.
I have asked HITEK Joe for a sample of the last TruBlu batch that went to the US so I can do a test on it with Known equipment, settings and Methodology.
Tazza...1000 yard stare...lol
Hooroo.
Regards, Trevor.
Australia
I have had four people look at the tru blu bullets. Each one gives a different color. Blue, bluish green,emerald. A lot depends on what light they are in. Everybody needs to remember something. Joe busts his hump trying to make what colors his customers want. According to Ausglock the guy don't ever sleep. As I understand the blue is very hard to get. We all have different reasons why we want a certain color. Don't always happen.
Boolits !!!!! Does that mean what I think it do? It do!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |