Have a 38 Super 1911 barrel.
Outside dimension is .498(,500?) so from post 1955.
Question I have is when did Colt make a barrel length of 5 1/2"?
Anyone have any insight into this additional 1/2"?
Thanks.
Have a 38 Super 1911 barrel.
Outside dimension is .498(,500?) so from post 1955.
Question I have is when did Colt make a barrel length of 5 1/2"?
Anyone have any insight into this additional 1/2"?
Thanks.
Last edited by kywoodwrkr; 03-12-2013 at 02:51 PM. Reason: Notification
If you aren't inteerested in using this barrel, send me a PM to see if we can dicker for the barrel.
Thanks,
Bruce
I Cast my Boolits, Therefore I am Happy.
Bona Fide member of the Jeff Brown Hunt Club
Cant say my post war is any longer than 5". Interesting possibility of someone changing it out later on. I know the feet on mine are worn at the lockup point so much that the slide moves forward another 1/8th inch no matter what length link I put in it. Time to weld it up and re-fit it. Put a 9mm barrel in there for the time being. Mine has no stamp on the barrel, but has the same colt bone ash bluing on the barrel as the slide. It fits 9x23 in it too without issue, but 38 super fit is a bit sloppy in the chamber. This is out of a super match. What is yours out of?
Bruce,
You have a PM.
xacec,
Was given the barrel(only) as a different caliber(38AMU).
It is 38 super as hood is for semi rim case.
It is full 5 1/2", not just a few thousandths over.
Picture is 5" compared to this one + 2 other pictures.
There is a three digit number stamped under barrel.
Thanks for any information.
Now you have me questioning my barrel. Mine is not cut for a semi rim case.No marking what so ever.
Dave,
Looking at pictures above, I'd recommend getting a chamber cast done on the barrel to verify the chambering as the barrel isn't cut for 38Spl based off what I saw in your photo. Considering the known age of the barrel , more than likely its a 38 Super cut to headspace off the rim.
Bruce
I Cast my Boolits, Therefore I am Happy.
Bona Fide member of the Jeff Brown Hunt Club
It's my understanding the later Colt barrels were not cut for the semi rimmed case, but were chambered to headspace on the mouth of the case ala 45 ACP.
In piddling about with the 1911,of which I am a neophite, and there is a whole lot not known, compared to what seems to be known or documented.
In trying to find out what this barrel went to, I just want to make sure I don't foul it up should it be useful, well more than just a regular 38 super barrel.
Had some feedback on the 1911forum.com but, well, I seem to get more information here.
Probably due to fact that the audience here, was there, and did that!
Thanks.
Last edited by kywoodwrkr; 03-13-2013 at 11:10 AM. Reason: spelling!
Leaves enough to thread for a supressor .
Both ends WHAT a player
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |