WidenersRotoMetals2Lee PrecisionMidSouth Shooters Supply
Reloading EverythingLoad DataTitan ReloadingInline Fabrication
Repackbox
Results 1 to 10 of 10

Thread: Need load data 40 cal tite group

  1. #1
    Boolit Mold
    Join Date
    Feb 2013
    Posts
    2

    Need load data 40 cal tite group

    I have some 40 cal 155 SWC laser cast bullets and I can't find any load data

    I also have some plated 180gr bullets I am trying to find a load for

    I have tite group, HS6
    If someone can help me find some load data it would help greatly

  2. #2
    Boolit Buddy joec's Avatar
    Join Date
    Apr 2012
    Location
    Lexington, Kentucky
    Posts
    400
    The Laser Cast Reloading manual doesn't list either of those powders. Now they do list the following though no min/max and it states not to use in a pistol with fully supported chambers. OAL 1.165 is the same for all.

    HP-38 4.9 @ 998
    Clays 4.0 @ 1000
    231 5.1 @ 1027
    WSL 4.8 @ 1029

    Lee's 2nd Ed doesn't list any of the powders either. Lyman's Cast bullet book doesn't list a 155 gr but does list a 150 gr for H-6 min 6.3 gr @ 1038 fps to max 8.8 @ 1224 fps. Lyman's 49th Ed. Lists only a 155 gr Jacketed Silver tip with H-6 with min 7.6 gr @ 988 to max 8.5 gr @ 1089 fps. Hopefully that will help.
    Joe

  3. #3
    Boolit Master kenyerian's Avatar
    Join Date
    Dec 2011
    Posts
    977
    Try this link for the 180 grain http://data.hodgdon.com/main_menu.asp.

  4. #4
    Boolit Buddy joec's Avatar
    Join Date
    Apr 2012
    Location
    Lexington, Kentucky
    Posts
    400
    Quote Originally Posted by Shooter.250 View Post
    I have some 40 cal 155 SWC laser cast bullets and I can't find any load data

    I also have some plated 180gr bullets I am trying to find a load for

    I have tite group, HS6
    If someone can help me find some load data it would help greatly
    Sorry I missed the 180 gr plated bullets completely.
    Joe

  5. #5
    Moderator Emeritus


    JonB_in_Glencoe's Avatar
    Join Date
    Mar 2010
    Location
    Land of 10,000 Lakes
    Posts
    15,830
    Quote Originally Posted by Shooter.250 View Post
    I have some 40 cal 155 SWC laser cast bullets and I can't find any load data. I have tite group, HS6
    If someone can help me find some load data it would help greatly
    I wouldn't use titegroup with cast in 40.

    Lyman castbullet handbook #4, lists a 150gr. cast bullet
    7.5gr starting load of HS-6 (8.8grMAX)

    I hope this helps.
    Jon
    ~~~~~~~~~~~~~~
    “If someone has a gun and is trying to kill you, it would be reasonable to shoot back with your own gun.”
    ― The Dalai Lama, Seattle Times, May 2001

  6. #6
    Boolit Buddy Raven_Darkcloud's Avatar
    Join Date
    Jan 2013
    Location
    Banks, OR
    Posts
    105
    A good starting point for 155 with hs-6 would be 7.4gr for cast, but tite group at 4.6gr would have less smoke from what I have seen (ymmv) I have found that using data for the next up weight jhp is just about the starting load for cast. COAL is the part that you need to look around for but I am seeing 1.125-1.135 I use 1.130 on my wifes rounds as it runs well in her sig. With my hodgdon powder I use hs-6 for my carry rounds (more push) and tite-group for target and cast rounds. Tite-group will load more per lb too.

  7. #7
    Boolit Buddy
    Join Date
    Jan 2009
    Location
    South Louisiana, right between New Orleans and Baton Rouge
    Posts
    133
    I use 3.6 to 4g of TG with a 155g LRN with an OAL of 1.155 in my Para 1640. It all depends on what type of match I am shooting.

  8. #8
    Boolit Mold
    Join Date
    Feb 2013
    Posts
    2
    Thanks for the help
    I think I will use a different powder for the cast bullets

    I did load some jacketed and plated bullets in 9 mm and 40 cal and everything went well

    I will now bench both guns to see how we'll they are shooting

    Do any of you bench your semi autos ?

  9. #9
    Banned


    Join Date
    Mar 2009
    Location
    29˚68’27”N, 99˚12’07”W
    Posts
    14,662
    The reason for not using Titegroup in the .40 is that it gets very "spikey" with pressure near the top, maybe it's just me but it seems a lot worse in that tiny case than in other, more volumous cartridges. If you have an issue where you seat the boolit too deeply for the data you're using or if the boolit sets back in the case under recoil or chambering, it can be dangerous very easily.

    I use a lot of it in .40, but with mild loads, softer boolits, and my ducks are very much in a row with custom-sized expander spuds and boolit size/seating depth. Done properly for target-level loads, Titegroup is very clean and accurate.

    HS6 is excellent for the .40, but it's very dirty until you get the pressure up near the top.

    The loading data in Lyman #49 is very good data to go by for this, I recommend picking up one of those books.

    Gear

  10. #10
    Boolit Bub
    Join Date
    Dec 2012
    Posts
    43
    I have been using TG for some time now. I love the Berry's plated 180 gn with a starting load of 4.5 gns. I don't venture much past 4.7.

    Actually TG is good for most of my plated rounds. I load several thousand rnds of 9mm, 40 s&w, and 45 ACP. I use hp-38 and BULLS-EYE for 38 spl and .357.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check