Mihec GC or PB 358-165RF Group Buy

[KSH]

Is this still open?
If so, when is the expected delivery?

[bcr]

I'd like a 4C HP mold with round, penta and flat pins. I'd like 2x PB and 2x GC cavities.

I didn't see any mention of flat pins, presumably those are available like all his other molds? If not, I'll want a solid instead.

brichards aat optics daught arizona dawt edu

[Fire_stick]

Lists have been updated

[taugust]

I would like one of the:

4 cavity plain base solids.

g99jeb at aol dot com.

Thank you

[KSH]

Thanks for the response, I will add you to my list.

[Fire_stick]

For those considering this bullet, but concerned about their experience feeding the 180 version in their Rossi M92 lever gun.

I've found that a cartridge OAL of about 1.560" works great in my Rossi.

[kevmc]

[QUOTE=bcr;2469600]I'd like a 4C HP mold with round, penta and flat pins. I'd like 2x PB and 2x GC cavities.

I didn't see any mention of flat pins, presumably those are available like all his other molds?
Are the HP pins reversible to flat ???

[sparkz]

Plz put me down for
- $90 for 2 cavity round hollow point Brass Mold, Gas Checked, at .360dia. (pins penta and a Solid if we can't reverse pin )
Just to be clear, I want to cast a HP and a Solid so those are the needed pins,

and Idea what the HP wight might be?
the 165 is for a solid correct?

Sparkz1000 AT Gmail DOT Kom

Thanks
patrick

[Fire_stick]

[QUOTE=kevmc;2472868]

I'd like a 4C HP mold with round, penta and flat pins. I'd like 2x PB and 2x GC cavities.

I didn't see any mention of flat pins, presumably those are available like all his other molds?
Are the HP pins reversible to flat ???

I have emails in to Miha regarding the flat pins question. I do know that the standard pins are reversible.

[Fire_stick]

sparkz,

Based on my experience with the heavier bullet offered last year, I'm thinking 160-ish

[sparkz]

Okay good,, That'll do,

Patrick

[Bzcraig]

I'm in for a 2 cavity solid, no pins please.

bzcraigatgmaildotcom

[Fire_stick]

I'm in for a 2 cavity solid, no pins please.

bzcraigatgmaildotcom

PB or GC Bzcraig?

[Bzcraig]

PB or GC Bzcraig?

My apologies sir.......PB please

[Fire_stick]

Updated lists

[357maximum]

BTW, the standard C-358-180 as originally designed by Glenn and run as a group buy through lee by yours truly works better than great in my 20 inch Marlin 357 Cowboy, cycles fine and shoots super nice groups. The same 180 boolit actually allows me to touch rifling in my stock 10 inch contender barrel too.

[Fire_stick]

Thank you 357!

Yes, I worked with Glenn on this lighter design.

This past weekend, I shot several dozen of the 180 grainers through my Rossi Model 92. Fun, fun, fun! Water filled jugs don't stand a chance .

I'm ready for deer gun season.

[Fire_stick]

Lists have been updated

[dodgyrog]

Yes please.
4 cavity solid nose and plain base if still available.
Thanks

[357maximum]

Thank you 357!

Yes, I worked with Glenn on this lighter design.

This past weekend, I shot several dozen of the 180 grainers through my Rossi Model 92. Fun, fun, fun! Water filled jugs don't stand a chance .

I'm ready for deer gun season.

FWIW....The standard 180 by Glenn simply loves 16.5 grains of MP300 in my 20 inch Marlin Cowboy and it leaves at 1720 fps to boot. I tried the same load in my 10 inch contender because I simply had a bunch of em ( 500+ ) made up come sight in time so I figured WHY NOT?.....the 10 inch contender loves that load too, have not ran it over the screens yet in the 10 incher but it hits my 100 yard swingers and 1 whitetail fawn quite hard. It does not have as much muzzle flash as H110/296 either, but it is still a MAGNUM load.