put me down for a 4 cavity .358 plain base with all the pins
maderawood6 at geemail dot com
|
   
   
|
|
put me down for a 4 cavity .358 plain base with all the pins
maderawood6 at geemail dot com
Last edited by maderawood6; 03-11-2014 at 10:45 PM. Reason: dont know my own email
CPL Lou
Good day 45 2.1, looks like I was overlooked on the list, please see post #159.
Thanks & Best Regards,
Jon
No, you weren't overlooked, just located differently. When someone wants off (like in post #158), I put the next person in that place. You're in the #8 listing. Sometimes kinda hard to find when you expect to be at the end of the list.Originally Posted by rcwarship
Oooops, my bad. You are exactly right, I expected to see it at the end & did not think to look elsewhere.
Thank you very much for the info & especially for doing the work on this thread. You the MAN!
Thanks Again & Best Regards,
Jon
14 months - I know Mihia has his own schedule but jeeze...
One 4 cavity 0.366" plain base mold with penta HP pins please.
ballistim(at)yahoo(dot)com
“Men occasionally stumble over the truth, but most of them pick themselves up and hurry off as if nothing ever happened."
― Winston S. Churchill
This isn't as old as some other GB's. Patience is one of the virtues.
Thread updated.................
I'd like a 4-cavity, non-GC, 0.358", Large HP please....
kef762 AT yahooDOTcom
Last edited by tiger762; 04-01-2014 at 10:58 PM. Reason: forgot the disguised email address...
Still don't see me on list, am I just not seeing it?
“Men occasionally stumble over the truth, but most of them pick themselves up and hurry off as if nothing ever happened."
― Winston S. Churchill
Oops, spoke too soon! Sorry...
“Men occasionally stumble over the truth, but most of them pick themselves up and hurry off as if nothing ever happened."
― Winston S. Churchill
What grain is this?
That's shown on the drawing in post #1...... Approximately 96 gr. solid or 87 gr. hollow point dependent on choice of diameter and alloy.
I would like to be on the list for this one.
g99jeb at aol dot com
One 4 cavity 0.358" plain base mold with a penta and a blank pin.
Thank you.
Tom
Put me down for one 4 cavity 0.358" plain base mold with a penta and a blank pin.
ffrisby AT hot mail dot com
Thanks
I'm #40 on the list. Please remove the handle option that I requested.
Thank you!
Miha just closed a gb on a 40 cal that isn't as old as this one (started 4-20-13) - hope we haven't dropped below his radar.
No.... GB's don't go in order most of the time.
Thread updated.................
I'm new to this and hope I did this right. And I hope I can get into this buy. Please let me know what else I need to do. Thanks.
I would like (1) one 4 cavity .358 plain base mold with the penta pins.
Jdarmament at gmail dot com
Thread updated.................
Posting Permissions
| BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
| BR | Bench Rest | M | Magnum | RN | Round Nose |
| BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
| C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
| HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
| PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
| LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
| GC | Gas Check |
Reply With Quote