MiHec 2 or 4 cavity brass 358640 380 ACP/ 9mm Luger & Makarov Cramer HPGC or PB

[FatMcNasty]

45 2.1 can you remove my name from the list. I had some things come up. And cannot participate.

[sparkz]

Ok Il Bite,

2cav (first Choice)
4cav (second Choice)
diameter? .... 0.358" (for my Colt Goverment 380acp so i think thats right size, to size down to 356)
Gas Checked,
with HP & penta HP, 1 set each total 2 (Pins to make it a RN Boolit come with the mold, correct?)

Sparkz1000 AT GmAiL Dot Com-awn


any est on when these may show up?
I know it's worth wait and I plan on a long wait
just wondering does this go in faster as its an older GB


TIA
Patrick

[funshooter]

I will take a 4C brass mold hp with all the pins .358 PB and a handle
weldinspector at earthlink dot net

[gtgeorge]

Please put me down for one 4 cavity, all pins, PB .358 gspatton at gttransmissions dot com.

[45 2.1]

Reply to sparkz:

(Pins to make it a RN Boolit come with the mold, correct?) No, this mold is a flat nose, it looks like the picture in the first post.

any est on when these may show up? No estimate..... a guess would be a quite a while. MiHec closes the GB when he is ready to make it.

Thread updated.............

[Buzz64]

MiHec just closed another GB I'm on (10mm) with over 75 on it. Yep, it will be awhile...

[USSR]

45 2.1,

Gonna have to drop out of this group buy. I need a mould sometime this century, and ordered one that is already made and ready to ship. Thanks.

Don

[TMSCU]

I will take a 4C brass mold Gas Check HP with all the pins .358
email: tmoyer1952 at yahoo dot com
My Cast boolit name is TMSCU
Thanks

[uncleskippy]

I would like a One 4 cavity 0.358" plain base mold with all pins
danielap at forsyth.cc

Thanks

[Low Budget Shooter]

45 2.1, please change my pins to large HP and plain. Thanks, LBS

[sparkz]

@ .45 2.1,, Right, sorry I ment a flat nose pin so I have choice of 3 boolits, 1) a Hollow point, 2) Smaller penta HP, and 3) Pins to make it a Solid FN Boolit, so like 3 molds in one seems like a great Idea for this little bad Boy, haha,,



Thanks Again for all your efforts to draw us all in one place for a great mold like this,
And ya have to know something like a nice custom as this one is, is worth the wait
Just Ichie to Pop a few with this one sorta gives new life to a old toy,,


Keep me in the loop
Patrick Campbell

Reply to sparkz:

(Pins to make it a RN Boolit come with the mold, correct?) No, this mold is a flat nose, it looks like the picture in the first post.

any est on when these may show up? No estimate..... a guess would be a quite a while. MiHec closes the GB when he is ready to make it.

Thread updated.............

[freebullet]

I'm out, please take me off the list.

[alha]

One 4 cavity 0.358" plain base mold with all pins &
One 4 cavity 0.366" plain base mold with all pins

both in the GC version

snowserver (at) hotmail d0t com

[sergraf]

I'm in for 1 plain base 4 cavity mold at .358 with all the pins and a set of handles if possible.

sergio underscore rafanan at yahoo dot com

[45 2.1]

One 4 cavity 0.358" plain base mold with all pins &
One 4 cavity 0.366" plain base mold with all pins both in the GC version

Just to clarify....... you have said plain base and gas check in the above. I put you down for two gas check molds. Is this correct?

Thread updated.............

[redneckdan]

Just to clarify....... you have said plain base and gas check in the above. I put you down for two gas check molds. Is this correct?

Thread updated.............

Please put me down for a 2 cavity .358 with the regular penta pins.


Dan

[BMKoenig]

Put me down for a four cavity, gas check, with large, penta, and solid pins. A set of handles as well.

rommelbmk (at) comcast (dot) net

[Dannix]

Interesting, nice big meplat on this boolit. If you can grow this design to 115grn for non-kurtz 9mm, e.g. 9x19mm, I'd have to bite.

(I already have your/Miha's 9mm 125 gr. HP, but I'm always willing to try any other non-kurtz 9mm designs you may come up with.)

[45 2.1]

Please put me down for a 2 cavity .358 with the regular penta pins.
Dan

Need a disguised e-mail address and the base style... either gas check or plain base.

Put me down for a four cavity, gas check, with large, penta, and solid pins. A set of handles as well.

I need the mold diameter you want... either 0.358" or 0.366".

Interesting, nice big meplat on this boolit. If you can grow this design to 115grn for non-kurtz 9mm, e.g. 9x19mm, I'd have to bite.

You won't need it with the HP, but you might get to see something like what you want.

Thread updated somewhat................

[BMKoenig]

.358 diameter