Mihec .22 for air rifles

[Baja_Traveler]

I think I'll throw the dice on this one...

kschuma1 at san dot rr dot com

[Airweaver]

Pakprotector..
The Fx is the old one with the LW barrel.
The Gb is still open.I talked to Miha and he said that he will cut it.Right now he is too busy and i don't know about his lead time.I hope we ll have news from him soon.

[Baja_Traveler]

Just to set expectations for everyone who does not know - with Mihec molds, take the attitude of "Good Things Come to Those Who Wait".

This will be my 3rd Mihec mold, and each of the previous molds have taken just about a year to hit my door. I'm also on the Miha 6.5 Cruise missile group buy, and it has gone much longer than that, but he is having cutting problems with that design, so understandable.

Have patients and you will have one of the best molds made - he is in great demand so the lead time reflects that...

[Airweaver]

Another notification i would like to add is that my design for this kind of tiny cavities need two cherries instead one due the small cherrys diameter.
So Miha needs more time to prepare them.
Also i asked from Miha to pay attention at dimensions tolerance,because this design can't be sizing.That means he will have many trials and errors until the final result .
As Baja said,"Good Things Come to Those Who Wait".

[lawboy]

I will take one.
Lawboy
Behightower@yahoo.com

[alha]

I'm in too. snowserverathotmaild otcom

[alamih]

put me on the list for one.
alamih gszabel@interia.pl

[BrassMagnet]

I would like one.
ronaldmeyers at optimum dot net

[Airweaver]

put me on the list for one.
alamih gszabel@interia.pl

LoL...You are already #5 on the list.

[jbelder]

Put me on the list as well please

[Airweaver]

I will..
...but it could be nice if you give me your e-mail please.

[jbelder]

jimelder42@gmail.com
Thanks Jim
Sorry Airweaver!

[rsterne]

The drawing is hard to read, but it looks like 5.62mm (0.221").... With airgun barrels typically running 0.217" groove diameter, how will this work?.... I thought 0.004" was too much to size....

Bob

[Airweaver]

I don't know for airgun barrels but LW airgun barrels normally measure 5.62mm groove diameter and 5.46mm land diameter with -.04 choke.
I have to admit that some airgun manufacturers(few of them) make special orders of their liking from LW and those barrels may differ from a standart LW but overall the size it's not being affected a lot.
As you can see the large bearing its only 1mm in length and it's responsible for the twist action ...so when you load,barrel became the sizer while it cut easily the large bearing and the bullet forms immediately and gets sealed too...
Instead other cast bullets,this one use land diameter to drive the bullet and keep it align until choked( reminds smooth twist ...it just keep twisted continously from the begining ).
Small bearing of Bullet i designed is 5.48mm....a little bit thicker than 5.46mm but after bullets entrance the expanding material fill "gaps" and bullet fit nice without need to push hard on the feeding.
Choke is another story and not ideal for bullets that their small bearing(bottom of circular slots) not even touch the barrels land diameter while groove diameter is the one which drive the bullet.
In that case you need to remove a lot material if you don't want the choke reacts negatively but there are also other factors which make it useless for a typical shelf bullet.

Guys be patient..Considering Miha's reply to me since the last 2 weeks,the blocks are ready and GB accomplish is on the way.

This is a group buy thread.For other questions please referring to the discussion thread. http://castboolits.gunloads.com/showthread.php?t=164775

[Nwaf2007]

Hi can you Put me on the list as well please

[Airweaver]

Off course.Your mail is Nobody@ZEROmail.com.. Right?

[Nwaf2007]

No this is my e mail
Nwaf-4@hotmail.com

[Nwaf2007]

Hi is my e mail in the list

[OLPDon]

Kindly cancel my order I am #15 on the list.
Thanks OLPDon

[Bruizer]

I will take one also, b dot rolfe1 at bellaliant dot net

Thanks
Bruizer