Please drop me from the list.
Gisli
Please drop me from the list.
Gisli
ok....me too...
one mold at .311...
gardensngoatsAAAAATTTTTTgmaildddooottttcom
One at .311 please
castboolits AAATTT lockport DDDOOOTTT net
“Our Constitution was made only for a moral and religious people. It is wholly inadequate to the government of any other.” - John Adams
One 4 Cav in .311 .. Please !! Thanks Coltman
randy3496 ATTGGGGGGGGGGGGGmailDOTcom
I would like one also,my first buy! bmnapper@@@@GGGGmailDOTcom
I'm already signed up for a .311 but I'm now wondering about a .316 as a paper patching boolet for shooting in 8mm rifles. Wonder if 150gr would be too light for that use?
I don't suppose it's possible to mix cavity sizes in the same block, is it?
NRA Endowment Member
Armed people don't march into gas chambers.
Opps I should have said the size, 0.311. One mold please.
I'm already signed up for a .311 but I'm now wondering about a .316 as a paper patching boolet for shooting in 8mm rifles. Wonder if 150gr would be too light for that use? It should work fine. As long as you can engrave the patch into the throat and keep the base of the patched boolit out of the powder room, it will work.
I don't suppose it's possible to mix cavity sizes in the same block, is it? He hasn't done that before and I doubt he will now... so no.
Thread updated...........
I'll take a 4 cavity at .311
kratzner (at) charter (dot) net
Last edited by Greg; 04-26-2013 at 10:16 AM.
God Bless ya'll
Greg
Je suis Charlie
"You can observe a lot by watching."- Yogi Berra
Shooters Talk Refugee
Interested in a 4 cavity plain base mould .311 diameter.
Rsaab (at) Panix dot com
please remove 20. Dwayneinfo.....Dwayneinfo AT yahoo DOT com.....one 0.311" mold
Dwayne
Never underestimate the power of stupid people in large groups.
If this is still open, please add me to the list.
One mould 316
janoosh357 a+t+gee mail dot com
thank you
Please remove me from the list for this group buy.
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
I'm ready to pull the trigger.
I would like a 4 cavity 311 mold as well.
I cast with a single cavity steel mold of the same profile and it seems like a nice boolit that is cheap to shoot, but it takes sooooooooo long to get a pile of them cast. This mold will compliment my MP 45 270 SAA very nicely.
Thanks
CGT80 at AOLLLLLL dottttt cooooom
#21 - Please drop me from the list - Financial reasons - Thanks
“Our Constitution was made only for a moral and religious people. It is wholly inadequate to the government of any other.” - John Adams
Please remove me from the list.
#15. 762 shooter.
Hope for the best, plan for the worst.
My amendment can beat up your amendment.
I guess one can never have enough 30 caliber molds. One 4 cavity .311 mold please.
ballistim(at)yahoo(dot)com
“Men occasionally stumble over the truth, but most of them pick themselves up and hurry off as if nothing ever happened."
― Winston S. Churchill
Any scheduling updates?
45 2.1,
Please remove me from the list. I'll need to pass on this.
Thanks
Is this buy closing soon? I might be in for a .311 but it will depend on time.
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |