Graf & SonsStainLess Steel MediaTitan ReloadingRotoMetals2
Lee PrecisionMidSouth Shooters SupplyADvertise hereInline Fabrication

Page 3 of 3 FirstFirst 123
Results 41 to 51 of 51

Thread: 577/450 Martini Henry Case Problem

  1. #41
    Good Afternoon. Been shooting a Mark I/II for 4 years and just use 80gr FF with carded wool to fill the airspace. The smell is interesting and I do get a slight snowstorm but no other issues. In fact, this beater of a rifle hits the black at 100 yards with me shooting off the table, trifocals, and a 60 year old pair of hands. My cartridges are 24ga formed metallic shotgun shells and they started splitting after 3.5 years of moderate use and abuse. Keep it simple and enjoy, Randy.

  2. #42
    Boolit Buddy bigbore52's Avatar
    Join Date
    Feb 2015
    Location
    Australia
    Posts
    53
    If I can add my two bobs worth - been shooting the 577/450 for many decades now and never had a separation.....I would suggest it could be a combination of factors such as have already been described. Either a weakened case, wrong loads or fillers and or a combination thereof...

    Can I suggest you try going back to basics with it? By that I mean trying to duplicate or as close as possible the original loads they used as some knowledgeable folk have posted already?

    For example, I use Bertram Brass with 90gn of Swiss Fg under a cardboard spacer then felt wads to take up the volume so there's no air gap under the pill..I do not compress the powder and wad merely lightly tamp it down with a wooden shaft to sit them snug ..on top of that I use a lubed 570gn lead pill based loosely on the Postell but at .460 diameter (mould made by CBE) and with a 20:1 (Pb:Sn) brew. There's really no need to harden it with Sn but I add it because I make other loads with the same batch..... .the Postell will work just fine as it is but accuracy may be affected if your bore is not 458 and I can guarantee you it won't be ... I will often use a bees wax lube cookie under the pill but as the pill is already lubed it's not that necessary and often I don't bother with that separate lube.....the original load did use it........

    I have used a variety of fillers over the years and they all gave me headaches of one sort or another but eventually settled on felt wads as that was what was originally used...and believe it or not, I get the best results from it...........interestingly the felt I use comes from the same company that made it a hundred years ago in the UK - they will do mail order and you can order it in a variety of sheet thicknesses to make up the gap space you need - details are : Hardy and Hanson in West Yorkshire http://www.hardy-hanson.co.uk/felt_strips.htm - worth dropping them a line and asking.....

    you need to ensure there is minimal air gap between the powder and the pill........easy enough to work out the thickness of wad you need and then just order that thickness sheet or make it up form different sheets as I do......

    I use their felt in most of my BP loads in other calibers and have never had any issues or problems with it.....just make your punches to suit or you can buy them at various sources such as Track of The Wolf and others.... ..when it's all said and done with these old rifles, it behooves a certain feeling to use "original" components wherever possible.......good luck with it and I hope you sort it out quickly....Lee

  3. #43
    Boolit Master
    Join Date
    Sep 2010
    Posts
    329
    i use a cotton ball over the powder, it weights nearly nothing and takes up the air space in the case. then a grease cookie under the bullet.

  4. #44
    Boolit Buddy yulzari's Avatar
    Join Date
    Jun 2014
    Location
    France Nouvelle Aquitaine
    Posts
    59
    I have tried most fillers in the 577-450 cases over the last few years bar granular fillers as these clump into a hard plug just like the dry sharp sand used to block the open end of shot holes in blasting rock. I finally settled on raw wool, of which I have an infinite supply free, packed in fairly firmly. Then I was led to try foam backer rod. The closed cell foam sold in rolls to take up the gap when installing windows. Available at any hardware emporium. Ideal. Just measure off enough to slightly over fill the gap and cut as many as you need to the same length. Same weight every shot. If you do not crimp your bullet and find that the foam's 'spring' pushed the bullet out a bit further than you wanted? No problem. When chambered the bullet will bottom out in the throat and get pushed back in to the ideal just touching the rifling. The same every time. Whilst I just leave air in service 85 grain charges I can get down to 45 grains for 100 metres with all the space filled up with foam backer rod.

  5. #45
    Boolit Mold
    Join Date
    Feb 2008
    Posts
    13
    I used to use semolina as a filler in some of my bp cartridge loads , but stopped doing so when a fellow shooter at my club told me that he had experienced problems with the semolina " caking " in the cartridge case and adding quite significantly to the rifle's recoil . I never experienced any problems , but decided to stop using it anyway.

  6. #46
    Boolit Master

    Newtire's Avatar
    Join Date
    Mar 2005
    Location
    Star, Idaho
    Posts
    2,653
    Quote Originally Posted by yulzari View Post
    I have tried most fillers in the 577-450 cases over the last few years bar granular fillers as these clump into a hard plug just like the dry sharp sand used to block the open end of shot holes in blasting rock. I finally settled on raw wool, of which I have an infinite supply free, packed in fairly firmly. Then I was led to try foam backer rod. The closed cell foam sold in rolls to take up the gap when installing windows. Available at any hardware emporium. Ideal. Just measure off enough to slightly over fill the gap and cut as many as you need to the same length. Same weight every shot. If you do not crimp your bullet and find that the foam's 'spring' pushed the bullet out a bit further than you wanted? No problem. When chambered the bullet will bottom out in the throat and get pushed back in to the ideal just touching the rifling. The same every time. Whilst I just leave air in service 85 grain charges I can get down to 45 grains for 100 metres with all the space filled up with foam backer rod.
    I have heard of the foam backer rod so loaded some up using that but wasn't too sure about trying it out. Once it warms up a bit and I have recovered from getting a new knee, I'm gonna go out & try this gun out.

  7. #47
    Boolit Master
    Join Date
    Nov 2017
    Location
    brisbane ,qld,australia
    Posts
    431
    I havent tried the foam rod yet,but if I can get it here I will.Its recommended by a number of notables in the component supply trade.It may well be the answer to shooting smokeless in these cases.......in regard to cases,I use 24ga CBC,and Ive found that with paper patched bullets cases last indefinitely,as there is little or no neck expansion.......but when I use tightly seated 476 bullets,necks expand out to chamber size,and it appears the cases are under considerable stress.
    .

  8. #48
    Boolit Master


    DxieLandMan's Avatar
    Join Date
    May 2012
    Location
    Alabama
    Posts
    232
    Quote Originally Posted by toot View Post
    i use a cotton ball over the powder, it weights nearly nothing and takes up the air space in the case. then a grease cookie under the bullet.
    This is what I use too. 75 grains of 2FF black powder, a cotton ball and then a grease cookie.

  9. #49
    Boolit Master
    Join Date
    Sep 2010
    Posts
    329
    I fill up the air space in mine with RICE CRISPIES weigh nothing and do not turn into a solid slug when fired. smells like you are baking cookies!. I have used this method for many years with success.

  10. #50
    Boolit Master
    Join Date
    Aug 2009
    Location
    gardners pa.
    Posts
    2,713
    in George note's book cartage conversions he advises against cow filler in bottleneck cases. he also showed a outer case turned with a .45-70 case inside.then you can have reduced case volume.

  11. #51
    Boolit Master

    Newtire's Avatar
    Join Date
    Mar 2005
    Location
    Star, Idaho
    Posts
    2,653
    That sounds like a good plan! Also good for emergency rations.

Page 3 of 3 FirstFirst 123

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check