Should make a good 30-30 bullet with that flat nose. I can use it in 30-06, 300 win, and 30-30. Look at all the money I'm saving using one mold for 3 rifles. I'm sure the wife will appreciate my frugality.
Should make a good 30-30 bullet with that flat nose. I can use it in 30-06, 300 win, and 30-30. Look at all the money I'm saving using one mold for 3 rifles. I'm sure the wife will appreciate my frugality.
I know it's been asked in the discussion thread a couple of times but not answered. How well does this cycle in 300BLK. Is the nose smaller than .302? Also, has anyone tried these through a FAL rifle?
Oh Oh oh, Edit to ask: since I have a 30 cal plain base check maker I'd need this in a plain base configuration. Is this possible?
Last edited by L1A1Rocker; 06-04-2012 at 01:08 AM.
I know it's been asked in the discussion thread a couple of times but not answered. How well does this cycle in 300BLK. Unknown since nobody I know that has this mold has one of those. Is the nose smaller than .302? Its tapered, like most rifle throats are. Also, has anyone tried these through a FAL rifle? Not that I know of.
Oh Oh oh, Edit to ask: since I have a 30 cal plain base check maker I'd need this in a plain base configuration. Is this possible? Not on this GB
45 2.1 I would also like to know what the dia. is ahead of the taper portion? Is it .299, .300, .301 or .302 or ?
This country has gone to hell but now there is hope for us.
Thank you for the responces. The reason for the question on the nose diameter was not about the rifle throat but about the bullet feeding up the M-4 feed ramps of the AR type rifles. Here's a pic of what they look like.
Again, thank you for the responces. However, not knowing if this bullet will function in my BLKs and FALs (my main go-to rifles) I think I'll have to pass on this mold. It's kind of a bummer - I really liked the design and weight.
One MiHec 30 Sil Brass three cavity Hollow Point Mold, please.
lsunderhill---at---q---dot---com
I would like 1 mold! tagates at peoplepc dot com
I would like one as well.......hunchak ben @ yahoo.ca.......Thanks
List is up to date
I would like one too
j3526134 at telus dot net
Sorry, i just want one mold...
Got it covered Jet.
I will take one of these. jeff.girton at gmail dot com
I'm in for one mold.
dutch4122(at)yahoo(dot)com
-Matt
Group Buys Honcho'd: C326-175-FN, 434-210-RF, C434-210-RF, 30-165-SIL-MOD, 358156-PB, 413-170-Keith, C348-225-FN, 8mm SIL, 45-230-CM, 45-270-Ohaus/SWC, Edd's 28-170-FN
I'm in for one. sgpenney (at) gmail (dot) com
"Only accurate rifles are interesting."
- Colonel Townsend Whelen
May as well
gmsharps gmsharps at cs dot com 1 mold
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |