A buddy made me up a sizeing die for the .410s, he bored out an old 38 die and I did the final polishing, anybody know what shell holder will fit a .410? I can't find the one I had and don't remember the number. Will a 444 holder work?
A buddy made me up a sizeing die for the .410s, he bored out an old 38 die and I did the final polishing, anybody know what shell holder will fit a .410? I can't find the one I had and don't remember the number. Will a 444 holder work?
.444 or .303 Brit will do nicely.
Thermal underwear style guru.
"Exclusive international distributor of Jeff Brown Hunt Club clothing."
Supplier to the rich(?) and infamous.
Cheers from New Zealand
Jeff.
Thanks Jeff...............steg
I use my .44 mag shell holder.
I went to my gunshop owner and we tried everything on the list 44mag. 444marlin, 45 long colt and a few more, nothing, then I said that someone recomended 303 british, fit like a charm, BTW he was opening up blister packed shell holders and taping them back up when they didn't fit, we were using his unfired shells too...............
If they are Magtech solid brass, the only thing I found that would fit them is a holder for 38-40 & 44-40 Winchester. It's a #35 RCBS. The 44 mag and 444 were both too small.
They were winchester HS
A .410 base is the same size as a .44 magnum case rim, what's the problem ???
Last edited by DODGEM250; 04-25-2012 at 09:33 AM.
The rim fit allright until it came to the body of the shell, the brass part was too big to go in. The shells were unfired factory shells. The only one that they fit was the .303 British...
Hello, an RCBS #43 shell holder is a perfect fit for a .410 bore case. Bought one today, and yes it fits.
So you could cross-reference with other makers, the metallic shells it fits are listed on the package as these:
.223 Win Super Short Magnum
.243 Win Super Short Magnum
.25 Win Super Short Magnum
.270 Winchester Short Magnum
7mm Winchester Short Magnum
.300 Winchester Short Magnum
.325 Winchester Short Magnum
You could not however punch out the primer using this shell holder, since the hole in the middle is too small. You could bore it out, but being hard metal it might be a tremendous pain. There are easier ways to remove .410 primers anyway.
TargetRick
The #9 Redding holder is a perfect fit but punching out primers only removes the primer and not the anvil cup so there are better ways to remove primers. I set the hull on a washer and use a primer punch rod from a Lee Loader and my arbor press or you could just whack it out in the whackamole fashion. Gp
A 9.3x74R shell holder also works with Cheddite hulls.
On my dillon 550 I use a 7mm mag shell plate. Works fine for on old one piece win aa hulls and new remington hulls.
BB
try the shell holder for 9.3x74r thats what i fireform my 3" brass 410's out of and factory loaded unfired plastics fit as well
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |