RepackboxLoad DataRotoMetals2Reloading Everything
Lee PrecisionMidSouth Shooters SupplyTitan ReloadingWideners
Inline Fabrication
Page 1 of 2 12 LastLast
Results 1 to 20 of 22

Thread: Martini-henry mark iv

  1. #1
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60

    Martini-henry mark iv

    Hello,
    I just purchased a Martini-Henry Mark IV in 577-450. I have been over on the Single Shot forum asking about loads and bullets. Most of the loads mentioned use BP, I was also looking at the idea of using smokeless power. I have some IMR3031, Trail Boss, and some .458 cast boolits I use for my 45-70. I have never paper patched before, I have been lurking on the forum and reading posts. I hope that I can use some of the components that I already have, makes my wife happier! Thanks in advance for any and all help and suggestions.

  2. #2
    Boolit Grand Master 303Guy's Avatar
    Join Date
    Oct 2008
    Location
    New Zealand
    Posts
    9,078
    Good to have you with us.

    I'm looking forward to the paper patched Martini. I seem to recall it being said it's a very strong action - can't stake my life on it.

    When I lost my new set of hornet dies, I set about finding an alternative and someone told me of his uncle seating boolits at the range into a 'paper cup' in the case neck. I developed a pretty effective way of doing it. His paper was loo paper, I used paper hand towel. Nothing to do with paper patching, I know but one never knows when that trick might come in handy.

    Anyway, all the best in your endeavour.
    Rest In Peace My Son (01/06/1986 - 14/01/2014)

    ''Assume everything that moves is a human before identifying as otherwise''

  3. #3
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    303 Guy,
    Thanks for the hello. I'm looking forward to being able to shoot the Martini. I have never owned one of these and think it will be all kinds of fun. I just want to be able to shoot it without hurting it or me. Also the lower the cost of each shot the more I can afford to shoot. Thanks in advance for any and all help and suggestions.

  4. #4
    Boolit Master pdawg_shooter's Avatar
    Join Date
    Mar 2007
    Location
    S.W. kansas east of dodge city
    Posts
    3,008
    For SMOKELESS patching, first slug the bore. Size the bullet to BORE diameter +.001/..015. Patch with 16# paper. Size to GROOVE diameter +.001/.003 or as large as will fit the throat. Good place to start.
    45 AUTO! Because having to shoot someone twice is just silly!

  5. #5
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    Pdawg shooter, Thanks for the info, I guess I really need to slug the barrel before I get ahead of myself. I put one of my .458 boolits nose first into the muzzle, it stopped at the first band. Does that sound like I might be able to use them even if I need to PP? Once again thanks for the help.

  6. #6
    In Remembrance



    curator's Avatar
    Join Date
    Mar 2006
    Location
    Fort Myers, Florida
    Posts
    1,383
    Clarks359,

    The MH MkIV usually has a groove diameter around .470-.472. The seven-sided Henry rifling is notoriously difficult to measure. You can probably use IMR 3031 in a reduced load but I prefer SR 4759. Some others use IMR4198 and Ross Siefried's 1/3 smokeless for black and dacron wadding formula.

    You can easily paper patch the .458 diameter bullets up to size and use them. The MH has a very long, tapered throat to accommodate black powder fouling. A bit oversize is no problem. Yes the actions are sturdy but also 130+ years old. Hot-rodding these old war-horses is asking for trouble.

    I have found the Lee .475-400RF bullet cast from 1/3 Wheel Weight alloy and 2/3 pure lead, to shoot very well in both my Martini Henry MkII and Mk1V. The mould costs around 20 bucks and casts easily. I lube them with Lee liquid alox (2 coatings)

    Another tip I'll pass on about loading and shooting the MH 577-450: Index your cases when first firing and there after. Many MH breech blocks are not perfectly perpendicular to the bore and case heads become slightly bent out of line. Indexing prevents this from becoming a problem. We see this with old rolling blocks as well.

  7. #7
    Boolit Master
    barrabruce's Avatar
    Join Date
    Feb 2009
    Location
    Far Nth Qld Australia
    Posts
    1,985
    Errrggghhhh!!!
    I do range officer duties and do the black powder day.
    The boys with the Martinis who use black swear by dry wrapping and a bit of tallow wax lube on them. They patch to the bore + a bit.
    They even hit the big black dot on the targer occasionally!!!!.

    Some used duplex loads of fast smokeless and home brew Black powder that sometimes smelt a bit uriney.
    Haven't seen them for a while thou.

    At least I don't have to put up with the endless "smokeless is impossible" and you have to "patch to bore not groove".

    Miss them thou

    You'll need a pith hat so you can shoot the Zulu's.
    Learn how to make a British square and all that.
    Barra
    Last edited by barrabruce; 03-07-2012 at 10:54 AM.

  8. #8
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    Thanks for all the help and info.
    Curator, thanks for the tip about indexing the cases. I would have never figured that out by myself. When you use that Lee boolit do you PP or use it as cast? Which powder and how much? How is the recoil with this load? I would like to find something that wasn't to harsh, I would like for my wife and son to shoot this rifle also.
    Barra, I have never been to a range with all BP shooters. I can only guess at the clouds of smoke and the smells. But being different is what keeps us going. Thanks to everyone.

  9. #9
    In Remembrance



    curator's Avatar
    Join Date
    Mar 2006
    Location
    Fort Myers, Florida
    Posts
    1,383
    The Lee .475-400RF is shot as cast with Lee liquid alox lube (two coats) My load is 23 to 25 grains of SR 4759 and a dacron "tuft" to hold the powder against the primer and get good ignition. I do not size my brass and these unsized lubed slugs are a nice "thumb fit." Recoil is much reduced compared to the service load of 480 grain slug and 85 grains of FFg black powder. If fact it is actually fun to shoot. Accuracy at 100 yards is as good or better than the service load but issue sights do not contribute to precision. A taller front sight blade is usually required as these guns shoot quite high. Apparently the recruits were expected to aim at the belt buckle for a head shot at close range.

  10. #10
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    Curator,
    Thanks for the help and load info. That sound like a load that would be mild enough for everyone to shoot. I'll try to remember to aim at the belly button. I was hoping to get to the range this weekend, but still waiting on the brass and dies. I like the idea of not having to size the brass, the longer it lasts the better. Once again thanks for your help.

  11. #11
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    Curator,
    A couple more questions I forgot to ask. The SR4759 powder is a IMR number? Also I was looking on the Midway website, they only list a Lee .476-400 mold. Is that the same or should I try other places? Once again thanks.

  12. #12
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    I got my brass and dies on Friday, didn't try to load any rounds yet. The .458 bullets are a tight in the case necks. I think when I fire these the neck should expand out to the chamber. Then I need to patch the boolits to that diameter. Can't wait to get to the range and put lead down range. Thanks

  13. #13
    Boolit Grand Master 303Guy's Avatar
    Join Date
    Oct 2008
    Location
    New Zealand
    Posts
    9,078
    The SR4759 powder is a IMR number?
    The answer to this one is yes.
    Rest In Peace My Son (01/06/1986 - 14/01/2014)

    ''Assume everything that moves is a human before identifying as otherwise''

  14. #14
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    303Guy,
    Thanks for the answer. I thought it was an IMR number, I bought some over the weekend. Hopefully I can load some rounds later this week and go to the range on Saturday. I will try to remember to take pics and post them. Thanks

  15. #15
    Boolit Buddy
    Join Date
    Jul 2009
    Posts
    344
    First fire form your cases, then set your bullet diameter with a paper patch to just thumb seating without sizeing the case necks. You can get away from sizeing this way and the brass will last almost forever. Use pure lead for the bullets, paper patch, then run them through a press mounted sizer, lube the paper before sizeing. You will find this size of bullets is somewhat bigger than bore size, but will do very well in the Martini's forceing cone. The toolman

  16. #16
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    Toolman,
    Thanks for the info. I think after the cases are formed I will have a better idea about the boolit size I need to use. If I can patch them and use thumb pressure to seat it will make the cases last a whole lot longer. Thanks Larry

  17. #17
    In Remembrance



    curator's Avatar
    Join Date
    Mar 2006
    Location
    Fort Myers, Florida
    Posts
    1,383
    clarks359:

    Yes, the Lee .476-400 is the correct mould. Sorry for the confusion. I found this bullet to shoot best in my MkIV which has a large bore. They drop from my mould at about .480 cast from 1/3 wheel weights, 2/3 pure lead. With two coats of Lee liquid alox lube the bullets are a nice friction fit in fireformed 577-450 cases made from 24 gage brass shot shells.

  18. #18
    Boolit Bub
    Join Date
    Apr 2008
    Posts
    60
    Curator,
    Thanks for all the help. I getting to borrow one of these molds from another forum member. After I fire form my cases I will try to cast some of these boolits and see how they fit my cases. Larry

  19. #19
    Boolit Master
    Newtire's Avatar
    Join Date
    Mar 2005
    Location
    Star, Idaho
    Posts
    2,926
    Hi Curator, I will give that Lee boolit a try. I have a Mk IV also and am only now learning about bore size differences.

    I bought one of the 475-500 gr. moulds from Martin at X-ring services and found a load of 4759 like yours. 23 grains gave me around 1050-1070 FPS with this book it. I went up to the 25 gr. charge but that’s not a recommendation. I haven’t tried real black yet (yeah, I know-terrible) as I already have a bad back and a big load of black sounds too punishing some days. Sure is a fun gun to shoot.
    Last edited by Newtire; 10-03-2020 at 02:06 AM.

  20. #20
    Boolit Master Bad Ass Wallace's Avatar
    Join Date
    May 2005
    Location
    Australia
    Posts
    1,957
    Rule 1: Black Powder ONLY in a antique rifle not proofed for nitro.

    Rule 2: Read rule 1 first!



    Slugging the bore of a seven groove barrel is a waste of time without specialist metrology equipment.

    Last edited by Bad Ass Wallace; 10-01-2020 at 10:25 AM.
    Hold Still Varmint; while I plugs Yer!

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Abbreviations used in Reloading

BP Bronze Point IMR Improved Military Rifle PTD Pointed
BR Bench Rest M Magnum RN Round Nose
BT Boat Tail PL Power-Lokt SP Soft Point
C Compressed Charge PR Primer SPCL Soft Point "Core-Lokt"
HP Hollow Point PSPCL Pointed Soft Point "Core Lokt" C.O.L. Cartridge Overall Length
PSP Pointed Soft Point Spz Spitzer Point SBT Spitzer Boat Tail
LRN Lead Round Nose LWC Lead Wad Cutter LSWC Lead Semi Wad Cutter
GC Gas Check