35 cal pointy aka 358365 NOE

[Blammer]

Shipped 1/26/13

1. Blammer 4C + HP; drill for probePAIDShipped 1/22/13
2. midnight 4C; drill for probePAIDShipped 1/22/13
3. bearcove 2C; drill for probePAIDShipped 1/22/13
4. hicard 4C +HP + 2 extra pins;drill for probePAIDShipped 1/26/13
5. crawfobj 4C + HPPAIDShipped 1/22/13
6. 94doug 3CPAIDShipped 1/22/13
7. doc stihl 5CPAIDShipped 1/22/13
8. chuck4570 5C + HPPAIDShipped 1/22/13
9.
10.
11.
12.
13.
14. nanuk 1C GC + HP + extra pin plus extra GC's to CanadaPAIDPP 10/24/12Shipped 1/26/13
15. plinkster 2C + HP + 2 extra pinsPAIDShipped 1/22/13
16. leftiye 1C + HPPAIDShipped 1/22/13
17. leftiye 1C + HPPAIDShipped 1/22/13
18. flycutter 5C + HP;drill for probePAIDShipped 1/25/13
19. james.358 3C + HP + 2 extra blank pinspaidShipped 1/22/13
20.
21. 2ndamendmentnut 4C all PBPAIDShipped 1/25/13

[hicard]

I wish that the top punch wouldn't leave a ring arount the ogive of the boolits. Anyone have a solution to that problem. I guess I could take a dremel grinder to the bottom of the top punch to see if it would help.

[Blammer]

Hicard yes I had that problem. take a piece of sandpaper, fine say 200grit or finer, put it around the nose of a boolit for that top punch, then spin the top punch by hand on the sandpaper boolit, It will take that "edge" off of the Top punch that is causing the ring. 3-4 turns and done.

[hicard]

I'll try that blammer, thanks.

[nanuk]

Blammer, the pics show a W I D E nose.

were those cast with a RG?

My order was with a standard mould HP'd.... would it have the same wide nose with the HP?

if FP'd, on one like mine, will the meplat also huge like the one in the picture?

[Blammer]

nanuk, those were cast with my 4C and one cavity was HP'ed. So you're mould would cast the same. If you just fill in the HP, that is what the FP will look like.

if you want some specific dimensions on them before I ship your mould, PM me I'll get them for you. I'd hate for you to get a mould you really don't want.

[FLYCUTTER]

Blammer we need a update on the few molds that were not sent out.

[Plinkster]

They appear to be unpaid...

[nanuk]

Blammer

no, they will work just fine for what I have planned.

I was not looking for a long range target boolit

I was looking for a medium range hunter.

I think these will fill that niche just fine!

it was just they looked to have a wider nose than the spec'd pic. and I was wondering if the RG's would be different than the single HP's.

I'm getting a couple Whelens, and have a 9.3x62 to PP in... it should work just fine as it is. In fact, it may work a bit better at a reasonable speed. After all, I was looking for a MOOSE boolit in 35cal. I think I found it!

[FLYCUTTER]

check again Pinkster, they are paid.

[Plinkster]

Ah, didn't see there were two listed as paid and not shipped, my focus was elsewhere.

[hicard]

Are we still waiting on 8mm GC's ?

[Blammer]

yes still waiting on GC's.

[chuck4570]

Got mine in the mail today. Thanks Blammer!

[midnight]

Looks like they're arriving in Wisconsin. Got mine today. Swede remembered to drill it for the probe.

Bob

[Blammer]

GC's arrived today! I will have all moulds shipped out Saturday!

[Plinkster]

Got mine and the pot is plugged in!

[Blammer]

updated all shipped this buy is DONE!