Mihec 429244 Cramer HP

[Lucas]

Hi Sam,
Hope you are doing well. My barrel slugs at 0.430, should I opt for the 0.434? Any advice would be greatly appreciated.
Thanks for the reminder. Been out of the country for a bit, sorry I did not reply sooner. Work computer locks us out of non company sites...

I would really like a 2 cavity in the following orders, but if unavailable I would like to order 1 of each in:

4 cavity Large Hollow Point $120
Small HP pins $16
4 cavity solid $90

Shipping $20 (would it be $20 for a single order of the above?)

Total: $246 (if another $20 shipping is required, no problem)

[sffar]

Hi Lucas,
Measure the throats of your gun(s) and get the size that's close but a little bigger.
I'll put you down for 4 cavity molds, and as interested in 2 cavity's as well.
Just a reminder; you can cast solids with the hollow point mold.
Sam

[simonjester76]

Sam,

Looks like we are very close...

Simon Jester

[Reload3006]

when do you expect to get this rolling? if its a couple weeks to a month out I will take a 4 cavity .432 solid pin penta pin

[sffar]

when do you expect to get this rolling? if its a couple weeks to a month out I will take a 4 cavity .432 solid pin penta pin

Not likely a couple of weeks or a month. More like several months, at least–can't be sure. Let me know what you'd like to do.
Thanks,
Sam

[Reload3006]

Why I asked was because yesterday I just dropped 166 to Miha on a .452-200 cramer LOL so if its going to be months out is even better put me down.

[sffar]

Updated.
Reload3006, sorry I misunderstood your meaning. Billing won't be for a while on this one!
I put you down for penta and plug pins. Thus, you'll have small HP pins, larger HP penta pins and flat pins (which allow the mold to be placed on a hot plate when casting solids). As I believe you know, any of the hollow point pins can be reversed to cast solids but they'll project from the bottom of the mold when doing so.
Answered the PM. Please let me know which address to use. Thanks.
Sam

[Reload3006]

Updated.
Reload3006, sorry I misunderstood your meaning. Billing won't be for a while on this one!
I put you down for penta and plug pins. Thus, you'll have small HP pins, larger HP penta pins and flat pins (which allow the mold to be placed on a hot plate when casting solids). As I believe you know, any of the hollow point pins can be reversed to cast solids but they'll project from the bottom of the mold when doing so.
Answered the PM. Please let me know which address to use. Thanks.
Sam

Great use the Dcrop one.

[Lucas]

Hi sffar,
Thanks for all of your help and advice. Please replace my previous two selections with this one. Please put me down for:

Quantity 1:

0.434" , 4 cavity ($120), Large HP and Small HP ($16), Plug pins (solids) ($16), Shipping ($20)

[sffar]

Updated.
You're welcome, Lucas.
Sam

[skimmerhead]

put me down for a 2 cavity but will settle for a 4 cavity if there is not enough interest in the 2 cav. i want .432 gas check with penta and plug pins.
captainbogg at viscom dot net

skimmerhead

[sffar]

Updated.
Welcome, skimmerhead.
Sam

[sffar]

Movin' on up!

[simonjester76]

Bump to the Top!

[gunsbrad]

oh cmon. somebody else gotta be wantin this one.

Brad Hurt

[tnek13]

If it is not too late please add me to the list. I have not done this before so let me know the process – Thanks
Order = 1 mold - 4C, .432 ($120), Small HP, add Large Penta HP Pins ($16), add plug pins ($16) and handles (?) Shipping ($20)
Email - -----atcomcastdotnet

[sffar]

Hello tnek13,
You've got it all right. I add you name to the list (post#3) and when the time comes for Miha to make the mold he'll send you an invoice. Not long afterwards he'll ship your mold.

Sam

[midnight]

All tnek13 needs to do now is disguise the email address. I guess the crooks have a way of scanning and plucking out email addresses so the can bother you. Telletoo at comcast dot net.

[Grandpas50AE]

Sam,
Please change my Penta HP pins to large HP pins. Thanks.

[sffar]

Sam,
Please change my Penta HP pins to large HP pins. Thanks.

I wrote to Miha some time ago asking about whether Penta pins were part of the design (if they were, probably they'd be the larger pins) but never heard back from him. I'll try again. 45 2.1's drawing certainly showed large and small hollow points, but the question of whether there'd be pentas is still open. If the large are pentas, then getting round ones might be a special request (and vice-versa). I know I need to get a definitive answer on this. I'll take the pentas off your order for now if you like, and I'll push a little harder to get this straightened out.
Sam