NOE 311465 122Gr. RN ( Loverin )

[SwedeNelson]

NOE 311465 122Gr. RN ( Loverin )

THIS BUY IS CLOSED



We will offer this bullet in .311", .314", .316" diameters.
We will also offer a FN


One size / nose configuration per block. (No mixing diameter or nose configuration)

Will get this buy on the schedule as soon as we get 15 orders.
We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.

Prices will be as follows:
Single cavity mould $68.00 Ea.
Double cavity mould $72.00 Ea.
Three cavity mould $79.00 Ea.
Four cavity mould $85.00 Ea.
Five cavity mould $92.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $10.00 Shipping/Handling.
Prices are subject to change at any time.

You can mix number of cavities in an order to make 15.
We will offer Gas Check or Plain Base on this bullet.

Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal account:
pbsco1@qwestoffice.net
Make checks and money orders out to:
NOE Bullet Moulds

Our mailing address is:
NOE Bullet Moulds
1645 W 150 N
Provo, Utah 84601
801 377-7289




Thank you for your interest in this buy.
Swede Nelson

[SwedeNelson]

List of orders
*1 10x 5 cavity RN GC .311
*2 10x 5 cavity FN GC .314
*3 dromia 4 cavity RN GC .311 drill for probe
*4 dromia 4 cavity RN GC .316 drill for probe
*5 rintinglen 4 cavity RN GC .314
*6 Dutch4122 5 cavity FN GC .314
*7 Dannix 4 cavity FN 2GC 2PB .311
*8 dg31872 4 cavity FN GC .311
*9 square butte 4 cavity FN 2GC 2PB .311
*10 square butte 4 cavity FN 2GC 2PB .314
*11 square butte 4 cavity FN 2GC 2PB .316
12 mag44uk 5 cavity RN 1GC 4PB .314
*13 rollmyown 4 cavity FN 2GC 2PB .311 drill for probe
*14 rollmyown 4 cavity RN 2GC 2PB .314 drill for probe
*15 rollmyown 4 cavity FN 2GC 2PB .316 drill for probe
*16 Rattlesnake Charlie 5 cavity RN GC w/HP
*17 Bodydoc 4 cavity FN GC .311
*18 scb 4 cavity RN GC .311 drill for probe
*19 largom 2 cavity FN GC w/HP .311
20 troy71mo 4 cavity RN GC .311
*21 Jeff Michel 4 cavity fN 2GC 2PB .311
*22 CENTEX BILL 3 cavity FN GC .311
23 KYCaster 3 cavity RN GC w/HP & extra blank pin
*24 Cimarron Red 2 cavity RN GC .314 drill for probe
*25 Larry Gibson 4 cavity RN GC .311
26 Nix 5 cavity RN PB .311 w/HP
*27 Olvern 4 cavity RN GC .311
28 HighHook 4 cavity FN GC .311
*29 coxd 2 cavity FN GC w/HP .314
*30 sffr 3 cavity FN GC w/HP .311 drill for probe
31 Slow Elk 45/70 3 cavity FN GC w/HP .311
*32 15bobcat 2 cavity RN 1GC 1PB .311
*33 cba257 3 cavity RN PB .311
*34 Kansas Ed 3 cavity RN GC .314 w/HP extra pin
*35 atom73 4 cavity RN GC .311 drill for probe
*36 TCFAN 3 cavity FN GC .311
*37 trail troll 3 cavity RN 1GC 2PB .316
*38 Janoosh 3 cavity FN GC .311
*39 Janoosh 3 cavity FN PB .314
*40 kbstenberg 3 cavity FN GC .311 drill for probe
*41 sneakyNL 5 cavity FN GC w/HP .311
*42 FLYCUTTER 5 cavity RN GC .311
*43 Cattleman 5 cavity RN 4GC 1PB w/2HP GC .311 drill for probe
*44 PB234 4 cavity FN 2GC 2PB .314
45 DeadWoodDan 4 cavity FN GC w/HP .314
*46 ballistim 4 cavity FN GC .311
*47 btreanor 5 cavity RN GC .311
*48 fishman 5 cavity FN GC .311 drill for probe
*49 Bjornb 4 cavity RN GC .311
*50 ammohead 4 cavity FN GC .314
51
52

(*) = Paid

Thanks
Swede Nelson

[10x]

Put me down for a .311 5 cavity RN GC

You have a spare money order that I sent you that should pay for it....

List of orders
1

Swede Nelson

[longbow]

Al:

I am really tempted on this one and just may do it!

I got questions though.

If I am interpreting your drawing right, for a 0.311" boolit the front two driving bands are 0.310" and the rest are 0.311"?

I am looking for either 0.315" in PB or 0.316" in GC. What would the front driving band diameters be for those?

If FN what size meplat?

If HP what diameter & depth?

Could two cavities of a four cavity mould be hollow pointed (say each end cavity)?

I know, lots of questions!

Thanks,
Longbow

[dromia]

1 x four cavity GC Drill for probe .316"
1 x four cavity GC Drill for probe .311"

[Greg in Malad]

I'll take a 5 cavity, round nose, gas check, .311 diameter.
Now I can finally retire my single cavity mold.

[SwedeNelson]

longbow

Posted a drawing that should help.
And yes the two top bands are .001" smaller
so it would be the same on the .314" and .316" diameters, .313" and .315".
And two cavities could be hollow pointed, one on each end.

Swede Nelson

[longbow]

Al:

Thanks for that.

I was leaning towards the 311410 (in 0.315"/0.316") but I really like this boolit and if I can get two HP cavities in 4 cavity PB mould... well, I can be bought!

Count me as on the fence currently but if this is a go then I will jump in for:

- 0.316" PB (0.315" front bands)
- 4 cavity
- 2 HP cavities

I would like a deeper HP than what you show but could make my own HP pins so not a big deal.

Thanks again.

Longbow

[rintinglen]

I'd like a 4 cavity .314 GC

[SwedeNelson]

Updated list
Bump
You can check the scheduale here:
http://castboolits.gunloads.com/showthread.php?t=130122

Swede Nelson

[longbow]

Bump!

Surely there has to be more interest in this little beauty.

[10x]

Bump!

Surely there has to be more interest in this little beauty.

There has to be - when (if) you find them on flea bay they sell for rather more than the NOE multiple cavity version.

[Dutch4122]

I'm in for:

.311" / 5 cavity with one cavity hollowpointed

.314" / 5 cavity with one cavity hollowpointed

.316" / 5 cavity with one cavity hollowpointed

All cavities FN style nose configuration.

All gas checked, please.

[Dannix]

Please put me down for a 4 cavity GC .311

Edit: FN

Thanks!

[kbstenberg]

I would like a 3 cavity GC at .311, Flat nose
Kevin

[kbstenberg]

Will you allso drill mine for your probe? PLEASE

[Greg in Malad]

Bump!

Surely there has to be more interest in this little beauty.

I think the problem may be that since used molds are nearly impossible to find, too few people know how good this design shoots.

[Dannix]

I think the problem may be that since used molds are nearly impossible to find, too few people know how good this design shoots.

I just hope I'm not risking too much going for it in FN form -- I've heard some very good things about this little guy. The 311410 was tempting, but this cute little 311465 won out.

[Dutch4122]

Swede-

Please also note that I would like all three of my molds to be cut with the "FN" nose configuration.

Also, probably just a typo, but you have me on the list for a .311" and two .314" molds. I would like one of each diameter; in other words, .311"- .314" - and .316"

Thanks!

[square butte]

In for a 3 cavity GC .311 - all Flat Nose. ?Why are we doing this at .311 and not .312 ?