thanks again for the info did you get the info needed for my order
thanks again for the info did you get the info needed for my order
Bump...............
after reading what I wrote it was rather confusing and made no sense but that's how I have been lately sorry for the confusion
email correction it should read
nschek214 at hotmail dot com
thanks bigboredad
Ok once again I will succumb to the temptation
Stoneaxe42 at Yahoo dot com small and penta pins
Compromise is giving up something you are unwilling to fight for! ΜOΛΩΝ ΛΑΒΕ www.concealedcarryofarkansas.com
HiVelocity03 at aol dot com. with small and large pins
Thanks,
HV
Life's biggest tragedy is we get old too soon, and wise too late.
Sign me up please.
1 with small and large pins pvolkman3 at gmail dot com
Thanks
High Hook
Yes please.
1 small pin and 1 Penta pin will be great.
email: mikerolly at hotmail dot COM.
Mike
If this is Brass I will take One with Small HP Pins and 1 set Flat Pins.
For the Flat Pins I meant Blank Pins. Oh heck they are for a flat point Boolit with nothing sticking out the bottom if that makes sense.
cstewart8 at satx . rr . com
Last edited by JesterGrin_1; 06-13-2012 at 11:18 PM.
If one sits in thundering quiet the soul dies slow instead of yell to the heavens for all to hear and behold the righteous and upstanding and ones of which should be held with tales of woe. By C.A.S. <--- Thats Me lol.
I would like to get in on this if its not to late.
One mold with large HP pins and one set of blank pins.
jacknjenn16 at aol dot com
Up dated................
I would like one as well - with all pins.
twiggs1 toyon.wiggs at gmail
Should size easily to .460 and .459 for a 45-70 marlin?
please sign me up also
MK1MICAH OLD-SCHOOL-VEEDUB@HOTMAIL.COM
1 two cav mold with small,large penta and blank pins
Liberty is not a means to a higher political end. It is itself the highest political end.
Man, I hope this goes into prodution soon. I'd like to put some deer down with this buoolet in October! This will be my fourth Mihec mold. Two in hand and one on the way and this one in waiting!
"He who walks with the wise grows wise,
but a companion of fools suffers harm."
Proverbs 13:20
[QUOTE=MK1MICAH;1758766]Should size easily to .460 and .459 for a 45-70 marlin?
I haven't slugged the bore yet on the Marlin I recently acquired in a trade. The only castings I have on hand large enough are pretty hard, cast for a 458 Win Mag. I know the only way to know for sure the correct size is by getting off of my lazy donkey and casting some pure lead slugs.
So speaking in general terms, are the Marlin 45/70 bores usually in the 459-460 range??
THX!! Your answer pretty well sums it up that there is only one way to find it out my bore size, the right way.
I was fortunate enough to get a pre-Remmy without the Mickey Mouse safety. I got it for a straight across swap for an Iver Johnson M-1 Carbine. My Marlin hasn't seen much previous use. The young guy I swapped with claimed it was left to him by his Grandpa. The only thing I've shot through it so far has been a half box of the new Hornady Lever Revolution and 3 rds of old Remington factory jacketed he gave me with the rifle. The Remington ammo's recoil was considerably stiffer than the Hornady. Via the irons I nailed a dirt clod at the 200 yard dirt mound with the Remmy ammo. The Remington ammo was loose so I can only speculate and assume by the recoil they were pretty heavy j-word slugs
I'm recovering from surgery so health permitting I'm really looking forward to making a lead slinger out of the Marlin. I have a shooting bud that has spent as few years developing or in his words "perfecting" a 45/70 load for his H&R Buffalo Rifle. Following his lead and advice I should get a good head start.
Hi -
Please add me to the list for one mold with blank and large penta pins. tomhuttton AT comcast DOT net
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |