MiHec 358156 HP or Solid

[Suo Gan]

Can't wait for this one. Bump

[Dirtdgger]

Sffar change mine to a 360 please.

[sffar]

Suo Gan, nice bump!
Dirtdgger, .360 it is.
Sam

[Jared]

I am interested in a .360" 4 cavity with both sets of pins. A two cavity would be my second choice.

agcatjhs at msn dot com

[pps]

2c .360 with extra set of penta pins (second choice 4cavity)

ericwverheul at gmail dot com 93245

[GLL]

Sam:

Change my 4-cavity request to a 2-cavity ! It may speed the race to 15 !

Jerry

[AnthonyB]

Two cavity .360 GC for me with all pins.
anthonybennett at comcast dot net
Tony

[sffar]

updated.

Jerry, please let me know if you want the 4C as a second choice.

Don't know when this mould will get cut, but likely a couple of months at least. I'm thinking both the two and four cavity moulds get made, and we hit fifteen plus on the pricier four cavity after the holidays. However, my crystal ball's been wrong before.

[mick27]

put me down for a 2cav gc /.360, w/ round pins.

thanks,
mick jones (mick27)
mjsharps at yahoo dot com.

[Iron Mike Golf]

I'd like a 4C .360 with 3 sets of pins (round, penta, solid). If solid pins are not offered, then a set of either round or penta and I'll grind them down.

Count me as a PB. GC if there's not enough folks wanting a PB.

sugdenjw at msn daht com

Thanks!

[sffar]

updated.
Mike,
I'll put you down as a 4C HP, with a PB first choice in parentheses w/penta pins, and blanks, if available. I really doubt we'll get a PB buy going here, but I'll note the interest. The round and penta pins can be reversed for making solids. The pin's long ends extend down, is all. I don't think Miha makes a special pin for solids yet, though I believe there was some talk of it. I'll ask, anyway. Sound good?
Sam

[Tazman1602]

One please: $90/2C + $16 extra pins +$15 shipping .360 diameter

email is: philo187 AT yahoo DOT com

Thank you for honcho'ing this one!!!

Art

[sffar]

Welcome, Art.
Updated.

[sffar]

Solid point mold prices and additional pin options added to first post.
Sam

[Jason Freeman]

One 4 cavity .360 GC Solid (2 cavity second choice)
One 2 cavity .360 GC HP (4 cavity second choice)
jasonlfreeman at bellsouth dot net
Thank You

[Lefty SRH]

I seemed to have missed something. Whats the boolit weight?

[sffar]

I seemed to have missed something. Whats the boolit weight?

The Lyman 358156 is a 155 grain solid, so the solid clone should be about the same, and I'm guessing about 140 grains in HP. I'll ask about getting a little more detailed diagram with that important information.
Sam

[PB64]

4 cavity (2 cavity is my second choice) .360 HP GC with all pins.
pw1340 at yahoo dot com

[sffar]

Updated.
PB64, I put you down for standard round and additional penta pins. Let me know if you wanted the plug pins and/or the "grind yourself pins" as well. HP pins can be reversed to cast solids, so unless having the HP pin sticking out the bottom bugs you the plugs aren't needed to make full use of the mold.
Sam

[PB64]

Updated.
PB64, I put you down for standard round and additional penta pins. Let me know if you wanted the plug pins and/or the "grind yourself pins" as well. HP pins can be reversed to cast solids, so unless having the HP pin sticking out the bottom bugs you the plugs aren't needed to make full use of the mold.
Sam

Thanks sffar, that works for me!