NOE 513 850Gr. FN Re-run

[SwedeNelson]

NOE 513 850Gr. FN Re-run




We will offer this bullet in our Deep Large Blocks, 3 and 4 cavity only.
Our deep blocks are 2” tall to fit very large bullets, and we use a 4 cavity size block
to cut the 3 cavity and a 5 cavity size block for the 4 cavity - for better heat control.

This buy is on the schedule.
We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.

Prices will be as follows:
Three cavity mould $110.00 Ea.
Four cavity mould $128.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $15.00 Shipping/Handling. (new USPS rates )
Prices are subject to change at any time.

You can mix number of cavities in an order to make 5.
We will offer GC or PB. But only one or the other per block.

Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal account:
pbsco1@qwestoffice.net
Make checks and money orders out to:
NOE Bullet Moulds

Our mailing address is:
NOE Bullet Moulds
1645 W 150 N
Provo, Utah 84601
801 377-7289


Thank you for your interest in this buy.
Swede Nelson

[SwedeNelson]

List of orders
*1 midnight 3 cavity GC drill for probe
*2 bbqncigars 3 cavity GC
*3 nytmtneer 3 cavity GC
*4 Japlmg 4 cavity GC
5 Aaron 3 cavity GC
6 Aaron 3 cavity PB
*7 timbuck 4 cavity GC
*8 timbuck 4 cavity GC
9 mroily 3 cavity GC w/HP
10 101coolcars 3 cavity GC w/HP
11 greywuuf 3 cavity GC w/HP
*12 fireball168 3 cavity GC drill for probe
*13 fireball168 3 cavity PB drill for probe
14 agent 4 cavity GC
15 Stryker 4 cavity GC
*16 DukeInMaine 4 cavity GC
*17 Salmon-boy 4 cavity GC
18 Carnivor878 3 cavity GC w/HP
*19 wellfedirishman 4 cavity PB
*20 Mikepb42 3 cavity GC w/HP
*21 Jeff Houck 4 cavity PB
*22 quasi 4 cavity GC
*23 ridurall 3 cavity GC
*24 MUSTANG 3 cavity GC
*25 MUSTANG 3 cavity GC w/HP
26 docstodd 3 cavity GC w/HP WILL CALL AT NOE
*27 HighHook 3 cavity GC w/HP
*28 Ken73 3 cavity GC
*29 rockrat 4 cavity PB
*30 scarry acarney 3 cavity GC w/HP
31 ov3rclock3d 3 cavity GC w/HP
*32 Indio 4 cavity PB
*33 Southpaw 3 cavity GC w/HP
*34 Bob J 4 cavity GC drill for probe
*35 mpkunz 3 cavity GC w/HP
*36 dead-bird 3 cavity PB w/HP
*37 4t5 3 cavity GC
*38 FLYCUTTER 4 cavity GC
*39 ilikec2 3 cavity PB
*40 atom73 3 cavity GC drill for probe
*41 catskinr 3 cavity GC
*42 Rollingblock45-70 3 cavity GC w/HP
*43 jk2008 3 cavity GC w/HP
44 whoever 3 cavity GC w/HP drill for probe
*45 HTRN 3 cavity GC
46
47
48


(*) = Paid

Thanks
Swede Nelson

[midnight]

Put me down for one 3 cavity gas check. drill for probe.


Bob

[frankenfab]

I don't even have a .50 BMG any more, and I still have an urge to buy one of these molds.

So, since I can't get in on the fun, here's some CAL .50 powrn for ya..

[bbqncigars]

Put me down for a three cavity GC. Also, what is the shank diameter and who makes checks that will fit these?

TIA,
Wayne

[midnight]

I get mine from Larry Blackman?. They are Gator checks. The 50BMG ones come in two lengths. Get the long ones. At least thats what my CBE mold needs. This mold looks to be almost a clone of the CBE mold. Swede should be able to tell us if that is the correct gas check. Someone on this forum sells Gator checks. I'll do a "Gator check " search and see who comes up. Larry is a dentist in Louisiana. When I called, his dental receptionist answered. That's the way it's supposed to be and she took my order. Larry had two orders to ship that day and he put them into the wrong boxes. A guy in Lacrosse, WI got mine and I got his. Larry sent us each 5 bucks and the guy and I swapped flat rate boxes. I hope Swede will chime in with the correct gas check for us. If he doesn't I'll PM him.

Bob

PS: My avatar shows the first iteration of my 50BMG. It now has a Magpul PRS and a billet steel single shot lower. A steel buffer tube, a 2lb Jard trigger,a CTK Precision monopod and a Bushnell 6500 2x16x42 scope complete the changes.

[midnight]

Some more 50 caliber porn.

[midnight]

Blammer is the one selling Gator check, but a check of the group buy section shows he doesn't have any 0.512 checks in stock.

Bob

[Bob J]

I have this mould and it really cuts the cost when shooting the 50BMG..... A couple of pics for you....

[midnight]

This is the Cast Bullet Engineering (Australia) mold I'm using now. It casts a 833gr linotype bullet.

[bbqncigars]

I just love good gun porn. Shooting cheap and shooting 50BMG is an oxymoron IMHO. I've got about 1500 virgin ball bullets on hand, but I just love to tinker. I modified the stock on my Windrunner to have an adjustable cheek rest, as well as being able to swap the bipod for an oak fore end that I use off the bench. EDM wanted over $500 for the cheek rest mod, and I couldn't justify blowing that on a change that took me four hours to d

[Bob J]

I just love good gun porn. Shooting cheap and shooting 50BMG is an oxymoron IMHO. I've got about 1500 virgin ball bullets on hand, but I just love to tinker. I modified the stock on my Windrunner to have an adjustable cheek rest, as well as being able to swap the bipod for an oak fore end that I use off the bench. EDM wanted over $500 for the cheek rest mod, and I couldn't justify blowing that on a change that took me four hours to d

Very true! Right now I am shooting mine over 190.0 grains of WC872 that I bought for $39/8 lbs..... They had an additional deal that covered hazmat if you bought enough.....

I cast mine with water dropped WW which I get for free from some friends at the local gas station.... Figure my cost per round is:

Primer = $.20
Powder = $.14
Gas Check = $.03

For a grand total of roughly $0.37 per round..... Sure takes some of the financial pain out of shooting the beast.....

[midnight]

Very true! Right now I am shooting mine over 190.0 grains of WC872 that I bought for $39/8 lbs..... They had an additional deal that covered hazmat if you bought enough.....

I cast mine with water dropped WW which I get for free from some friends at the local gas station.... Figure my cost per round is:

Primer = $.20
Powder = $.14
Gas Check = $.03

For a grand total of roughly $0.37 per round..... Sure takes some of the financial pain out of shooting the beast.....

I bought 6 jugs of WC872 also. I started with 195gr behind an 833gr linotype bullet. Got 2301fps and groups opened up to around 4in. Your 190gr load may be what I need.

Bob

[nytmtneer]

Very new to this casting thing, but put me down for a three cavity GC.
Thanks Mike

[Japlmg]

Put me down for one of the four cavity Gas Check molds.
Gregg

[Aaron]

Swede

I was thinking you ok'd PB offline. If so, I would like one 3 cavity PB and one 3 cavity GC.

Thanks

Aaron

[Bob J]

I bought 6 jugs of WC872 also. I started with 195gr behind an 833gr linotype bullet. Got 2301fps and groups opened up to around 4in. Your 190gr load may be what I need.

Bob

Mine lubed and gas checked came in around 870 grains (water dropped WW).......

My ladder actually started at 160 grains and came up in 10 grain increments.... Was getting smoked necks on 170 grains or less which to me indicated that I wasn't getting enough pressure to fully seal the neck.... 180 and 190 loads were much better with the 190 grain load effectively a 1 hole group at 100 yards which unfortunately is the only range currently available to me so can't speak much about the ballistics beyond that.... 1955 fps out of my gun (Bohica 36")....

Was loaded with fireformed brass, neck sized..... Lars carnauba red lube and sized to .513..... No sign of leading so far.....

Great plinking boolit......

[timbuck]

I always wanted a .50BMG. You have to start somewhere.

Four cavity mould $128.00 Ea.
Not in any hurry.

BobJ: I saw your pictures, you have small hands. ( big honking boolit)

[SwedeNelson]

Updated list
Bump

Use Gator checks (.512R Long)

Thanks
Swede Nelson

[greywuuf]

A couple of us got together and had a reamer commissioned that approximates the .510 whisper, (.338 Lap cut back to 1.88) Does anyone have an opinion on the suitability of this mold for that application?