I want one. And I'm gona hold my breath till I get one.
Matt Hooper
I want one. And I'm gona hold my breath till I get one.
Matt Hooper
I'll take one if they rerun them...
probably a 3 cavity if it matters..
I would like a 4 or 5 cavity mold !!!
I want one as well. 4-5 cavity!!
One more and we can get it started as a SGB
Schedule is booked in to August.
Swede Nelson
The expectation of evil is more bitter than the suffering -OR-
More people die from worrying about getting ate by a bear then get ate by a bear.
Make more this time...
Rich
Im going to suffocate befor aug. But that's about when my "form 1" may get approved.
Matt Hooper
I am interested. I'm new so I would like to know the expected price. Thanks
I also am interested. Can you remind me of the boolit dimensions? I wish to use it in a 303 barrel - so I would like it at .311 to .313 rather than .308... (2 or 3 cav mold.)
Mark
Ok, I quit being lazy and looked-up the original thread for specs etc.
I am in for a 3 cavity - 1pb 2gc with a hollow point on one of the gcs please.
Love it! Mark
Swede, do we have enough to go active?
Matt Hooper
ok last time i got a 2 pb 2 gc , but it looks like I am going to try to use the PB's mostly only my HP is a gc. maybe I ought to get another with a HP pb
put me down for another ... I will decide what configuration I want when it goes live ...
and that looks like 6 .. maybe 7
depending on the time frame I might be good for two
how many do we need to Not be a small group buy ?
Group buy is started and on the schedule
http://castboolits.gunloads.com/show...48#post1464848
Thanks
Swede Nelson
The expectation of evil is more bitter than the suffering -OR-
More people die from worrying about getting ate by a bear then get ate by a bear.
Is there a "results" thread? There's half a dozen of us in the "want to buy" section trying to get samples before we sink on a mould... Someone could make a few $'s helping us figure out if these will be the best thing since sliced bread (or not).
http://castboolits.gunloads.com/showthread.php?t=145597
"Reality is that which, when you stop believing in it, doesn't go away."
hello, I realize this buy is just about closed, but i have a question. has anyone used this in anything bigger than a whisper? what twists and velocities are we looking at here? my concerns are most of my 30 cal, which include naturally a 300 whisper, 30 herretts, 300 savages, 308, 06, are all 1/10 twist. It should stabalize in the whisper and herrett, but what about the faster stuff? thanks jim
I have used the Accurate Molds version of this boolit in my 30-06 at 1950fps (35gr H4895), it is a Savage with 1-10" holes at 100 and 200 are perfectly round.
I have not found much detail in the "results" thread..... I would be interested in more detailed range reports using both ARs and bolt guns...... Accuracy along with loads geared toward higher fps in .308 or 30-06.....
Thanks
Bump..... Anyone with more detailed results to post???
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |