WEBLEY 455-265-HB mould, 4 cavity brass Cramer style, Group Buy (GB) open

[dromia]

Welcome to Cast Boolits BTW.

[Onty]

Ok I just registered for the forum ( so hello Everyone ) now is this group buy still active, if yes how can I get in on this.

Welcome!

You just joined us. Now, I need your e-mail address (camouflaged), desired boolit dia (.455 or .457), and if you want blank pins for solid base, please list them.

Regards, Onty

[Dead Dog Jack]

Bump.

[Springfield]

Well, I've got two uncut Webleys, a MK 6 and a Mk 4, and an old Colt in .455 Eley, so I guess I better get in on this or I might regret it. A four cavity HB in .457 for me, please. whytelw AT comcast.net

[bonza]

4-cavity/.455 diameter/no extra base pins
arquebus1523 at yahoo dot com

[sandermar]

Just got wind of this group buy on the British Militaria Forum site. This site is just what I have been looking for since I am just going to be starting to cast my own boolits for some of the guns in my collection.

I would love to get a set of molds to cast for my Mark VI, in .455, with set of pins please.

paangaboat at yahoo dot ca

Thanks,

M.

[mech481]

will overseas orders be able to pay with paypal

[Onty]

will overseas orders be able to pay with paypal

Considering that Miha is located in Slovenia, I would think that PAYPAL should work from anywhere as long as you have major credit card.

[Dead Dog Jack]

Onty, did you mention this GB on the CanadianGunNutz forums? I didn't see it in the first 6 pages. If it's deeper in, I'll give it a bump.

[Onty]

Onty, did you mention this GB on the CanadianGunNutz forums? I didn't see it in the first 6 pages. If it's deeper in, I'll give it a bump.

No I did not, but that is not bad idea. BTW, you put it here http://britishmilitariaforums.yuku.c...y-bullet-mould ?

[Dead Dog Jack]

No I did not, but that is not bad idea. BTW, you put it here http://britishmilitariaforums.yuku.c...y-bullet-mould ?

Yep, that was me. I also put it on the British Gun Pub section on gunboards.com and the Canadian section on CasCity.com.

[Onty]

Onty, did you mention this GB on the CanadianGunNutz forums? I didn't see it in the first 6 pages. If it's deeper in, I'll give it a bump.

I just did it. As a matter I was thinking to do what you did on those forums, they are by far two best about British arms. Webley shooters in Canada usually go on one of those.

One smaller problem on CanadianGunNutz is they do not allow hot linking for non-supporting parties. But, would not hurt to do so, hope I did not brake any rule. Some forums insist to send them text for review. Will try to post on some other forums this weekend.

[vulture47]

Please put me down for one of the 455 HB molds, thanks Stewart. sdennis at ubtanet dot com

[tenexx]

Onty, I just saw the message on Canadian Gun Nutz, please put me down for a .455 diameter mold.

tenexx at gmail dot com

Thank you for your efforts.

[yardie]

Hello to all!!

Thanks for bringing attention to this over at CGN Onty!!

May I please order:

- 4 cavity (.455 diameter) mold
- Plain base pins.

o2thief at hotmail dot c0m

[Danceswithempties]

Good Day All,
Heard about this over at CGN.
You can put me down for one 4 mold in .457 & one .455 diameter and an extra set of pins.
Thanks for arranging this buy.
Danceswithempties at hotmail dot com

[happy7]

info at mattsbullets dot com

[Onty]

I need boolit/mould dia (.455 or .457) and/or e-mail address from following members. Also, let me know if you want solid base pins.


8. Colonel Flashman: e-mail and dia

11. broomhandle: dia
12. herbert buckland: e-mail and dia

15. bydand: dia

29. vulture47: dia

Other members; please check the list for accuracy.

Please, from now on, post any additional info or correction here on the thread, even if I contact you by PM. It's much easier for me to control what I had done (or missed) than check this thread, PM and the PM from another forum. And hey, you will keep thread bumping up to the top .

[PB234]

Question, if one is shooting a 455 Webley and the hollow base should expand to fill the bore why does one want a 457? Just a new caster asking to be informed. thanks

[Doctorbowie]

I would like to put in for a .455 diameter mould.

doctorbowie at yahoo dot ca

Thank you