h1tdk00
This groove is wide enough that its not a problem.
But yes a round groove will generally drop easier.
Swede Nelson
h1tdk00
This groove is wide enough that its not a problem.
But yes a round groove will generally drop easier.
Swede Nelson
The expectation of evil is more bitter than the suffering -OR-
More people die from worrying about getting ate by a bear then get ate by a bear.
Mr. Nelson, I hope you don't mind a few more questions.
Is that a bullet that you already have cherries for?
Would it be possible to bevel the base a little on that bullet and would that increase or decrease the weight of the bullet?
Can you do brass and aluminum molds in the same run, or do we have to agree on one or the other?
Thanks,
Tim
I want I want I want! I like the brass because to me it seems to hold up better over the long hall, and for me anyway here in the cold climates they hold heat better during cold casting sessions!
See Some of My Holster Work Here:
www.whitetigerleatherworks.com
me too!
RG-4 is all I'm asking for...
Rich
h1tdk00
No this is a new design, so we would need 15 orders.
We could make it a bevel base but the weight would go up.
Brass takes different tooling than Aluminum so we would need 15 orders of both
to do brass and aluminum.
Hope this helps
Swede Nelson
The expectation of evil is more bitter than the suffering -OR-
More people die from worrying about getting ate by a bear then get ate by a bear.
All else fails, you could get Tom at Accuratemolds to do it. Give him a call. He'll add your design to the catalog, too.
--------------------------------------------------------------
Young kid to old vet: "How do I know when it's time to take up arms?"
Old vet: "Well, you grab your rifle, load 'er up and go outside........ if you're the only one, it ain't time yet!"
I'm hoping we can get enough for Sweede as he is the one who put in the work so far
See Some of My Holster Work Here:
www.whitetigerleatherworks.com
harley45
Thank you
That's why some of the other bullet designers
don't like to put up detailed drawings.
Swede Nelson
Last edited by SwedeNelson; 02-17-2012 at 12:00 PM.
The expectation of evil is more bitter than the suffering -OR-
More people die from worrying about getting ate by a bear then get ate by a bear.
Your welcome, but I still want brass.
See Some of My Holster Work Here:
www.whitetigerleatherworks.com
So, has anybody thought to do a count of "I want"s yet? I have been following this for a while and think there are pretty close to the required minimum of 15 moulds. I am not ready to commit yet, but it wouldn't take too much arm twisting to get me there. Timing is going to be key to whether or not I will be able to get in on this buy.
List as I see it.
1 harley45 (brass)
2 Idaho Sharpshooter
3 h1tdk00
4 starreloader
5
6
7
8
9
10
Copy and add your name if you are interested
Swede Nelson
The expectation of evil is more bitter than the suffering -OR-
More people die from worrying about getting ate by a bear then get ate by a bear.
Aluminum or brass? Brass or aluminum?
NO preference, as long as it is an RG-4...
Rich
1 harley45 (brass)
2 Idaho Sharpshooter
3 h1tdk00
4 starreloader
5 thumper, eh?
6
7
8
9
10
I hope I did this right; aluminum is fine, need 4 or 5 holer, 140gr TC works for me.
I vote aluminum.
Swede, is there anyway to get a sprue plate cutter like the Lee 6 cavity molds have? I don't like having to use a mallet when I cast?
I vote Brass! Hey i'm from Gary Indiana people vote two or three times here all the time!
See Some of My Holster Work Here:
www.whitetigerleatherworks.com
oldie but a goodie, I'd be very interested in a 40-135, solid or HP, aluminum 4-cav minimum
Possibly interested, can we get Al to repost a drawing?
More "This is what happened when I,,,,," and less "What would happen if I,,,,"
Last of the original Group Buy Honcho's.
"Dueling should have never been made illegal in this country. It settled lots of issues between folks."- Char-Gar
ok, another month or so has passed by, I've been thinking about this one and would enjoy an opportunity to sign up, brass, aluminum, what ever......come on out there!
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |