NOE 225 62Gr. FN (MX3-22 EX)

[SwedeNelson]

225 62Gr. FN (MX3-22 EX)
Here is the link to the discussion thread:
http://castboolits.gunloads.com/showthread.php?t=106634



Will get this buy on the schedule as soon as we get 15 orders.
We will keep the buy open until 2 or 3 weeks before the date on the schedule.
At that time we will close the buy and send out a PM with
a request for payment. We don’t require payment before then.

This buy will be on our SB (Small Bore) moulds.
This is a down sized mould for better heat control.

Prices will be as follows:
Single cavity mould (Standard Size mould) $68.00 Ea.
Double cavity mould (2CSB) $72.00 Ea.
Three cavity mould (3CSB) $79.00 Ea.
Four cavity mould (4CSB) $85.00 Ea.
Five cavity mould (5CSB) $92.00 Ea.
Plus $10.00 Shipping/Handling.
Foreign orders are a additional $10.00
Prices are subject to change at any time.

You can mix number of cavities in an order to make 15.
We will offer gas check or plain base on this bullet.

Use LEE Commercial 6-Cavity handles (not included).
Lyman, RCBS type top punch furnished with each mould
as well as a sample of Bull Plate sprue plate lube.
Moulds are machined from 2024 Aluminum
Used for high strength structural and aircraft applications.
Tensile strength range 30,000 to 63,000 psi
Sprue plate (blued), alignment pins, and hardware will be
carbon steel.

Hollow pointing one cavity and furnishing a double
ended pin would be $35.00 Extra.

We will accept Checks, Money Orders and Pay-Pal
Pay-Pal requires a 3% sir-charge.
Pay-Pal acount:
pbsco1@qwestoffice.net
Make checks and money orders out to:
NOE Bullet Moulds

Our mailing address is:
NOE Bullet Moulds
1645 W 150 N
Provo, Utah 84601
801 377-7289




Thank you for your interest in this buy.
Swede Nelson

[SwedeNelson]

List of orders
*1 HARRYMPOPE 3 cavity GC
*2 357 Voodoo 4 cavity GC
3 tonyjones 5 cavity GC drill for probe
*4 BCall 5 cavity GC
*5 dromia 4 cavity GC drill for probe
*6 rhbrink 2 cavity GC
*7 shooter93 3 cavity GC
*8 CWME 5 cavity GC
*9 Doc Highwall 4 cavity GC drill for probe
*10 Bodydoc447 5 cavity GC
11 DiamondD 5 cavity GC w/HP
*12 WKAYE 2 cavity GC
*13 frankenfab 4 cavity GC
*14 rwjshooter 3 cavity GC
*15 dualsport 3 cavity 3GC
*16 madsenshooter 2 cavity GC
*17 MTCambers 5 cavity GC
*18 Czech_too 4 cavity GC
*19 DragoonDrake 4 cavity GC
*20 DragoonDrake 4 cavity PB
*21 badbobgerman 5 cavity GC
*22 SprueU 5 cavity GC
*23 quasi 5 cavity GC
*24 KennethF 4 cavity GC
*25 missionary5155 3 cavity 2GC 1PB
*26 OLPDon 5 cavity 4GC 1PB, w/HP in 1GC
*27 taminsong 5 cavity GC
*28 Sac_fff 5 cavity GC
*29 DaveInFloweryBranchGA 5 cavity GC
*30 oldfartz 5 cavity GC w/HP
*31 gmsharps 5 cavity 3GC 2PB w/HP 1GC
*32 LittleDoc 5 cavity GC
*33 JerryV 3 cavity GC
*34 Rusty W 3 cavity GC drill for probe Digital thermometer extra probe chamfer tool
*35 15bobcat 2 cavity 1GC 1PB drill for probe
*36 Max Brand 5 cavity GC
*37 Bob Maerdian 3 cavity GC
*38 Wayne S 5 cavity GC
*39 msgt1030 5 cavity GC w/HP
*40 fastasleep 5 cavity GC
*41 southpaw 3 cavity GC
*42 rockrat 5 cavity GC
*43 PB234 4 cavity GC
44
45


(*) = Paid




Thanks
Swede Nelson

[HARRYMPOPE]

3 cavity for me

HMP

[357 Voodoo]

4 cavity for me

thanks

[tonyjones]

I'll take a 3 cavity, drill for probe. What are the chances that you'll do the 55 grain as well?

Tony

[BCall]

5 cavity please! Unless we can get enough interest to run some 3 cavity bass ones as well? Thanks, Billy

[dromia]

Four cavity GC please.

[rhbrink]

Put me down for a 2 cavity with gas checks.

[shooter93]

I'll take a 3 cavity gascheck.

[CWME]

5 cavity GC please

[Doc Highwall]

four cavity and drill for probe.

[Bodydoc447]

I'd like a five cavity GC mould, please.

Doc

[DiamondD]

I would like a five cavity all GC with one HP cavity please.

[WKAYE]

Please put me down for a 4 cavity GC. Thanks.

[frankenfab]

How do you lube this boolit? Do you lube all the grooves, and if so, in a lubrisizer, do you get lube coming out around the top narrow band?

Or, do you only lube the grooves below the neck, or do you just pan lube them?

[Wayne S]

Al;,
Would it be possible to make the 2nd driving band from the bottom .225 instead of .223, that way, when sizing .225, lube won't leak past the .223 band.
The alternative will be to tumble lube them in the 45/45/10 mix. and I think that will be way to much lube for 1700-1850 FPS , maybe, maybe not ??

[Doc Highwall]

I have been lubing the SAECO #315 tapered bullet with my SAECO sizer. Just don't try to put a lot of pressure on the lube and they come out good for me. I have been using Bull Shops NASA lube which does not require heat to flow.

[frankenfab]

Sounds good to me. I assumed the extra groove sticking out past the neck was for more lube for high velocity.

[frankenfab]

I will take a 4 cavity GC.

[HARRYMPOPE]

Sounds good to me. I assumed the extra groove sticking out past the neck was for more lube for high velocity.

I lube only the first two and shoot it in my 22-250's at 2100.Due to the taper it really gets out into the throat and engraves nicely.

these are the last few groups shot with the Eagan and a Savage 12 22-250(before i sold the gun) and 13.5 Bartlett 4759 "clone" surplus powder.Smallest is .204 and best group i ever shot with cast in any caliber.


HMP